If you wish to contribute or participate in the discussions about articles you are invited to join SKYbrary as a registered user

 Actions

Taxiway Collisions

From SKYbrary Wiki

Revision as of 23:46, 30 May 2018 by Editor2 (talk | contribs) (Prevention)
Article Information
Category: Ground Operations Ground Operations
Content source: SKYbrary About SKYbrary
Content control: SKYbrary About SKYbrary
Ambox content.png
The present article is under construction.
Reader enquiries are welcome, contact the editor: editor@skybrary.aero.
Ambox content.png

Description

An airport is a complex interface between the air and the ground environments, where access must be controlled and separation between aircraft or between aircraft and vehicular traffic must be maintained and optimised. While most occurrences on airport aprons and taxiways do not have consequences in terms of loss of life, they are often associated with aircraft damage, delays to passengers and avoidable financial costs.

This article examines collisions and near collisions whilst aircraft are on the airport manoeuvring areas inclusive of taxiways and ramp areas. The article On-Gate Collisions provides insight into aircraft collisions occurring whilst on, entering or leaving an assigned gate.

Occurrences

As previously stated, to ensure efficient and safe airport ground operations, separation between aircraft or between aircraft and vehicular traffic must be maintained and optimised. On occasion, however, minimum separation, particularly aircraft/vehicle separation is compromised. Whilst all events do not result in collision with an aircraft, the majority of taxiway occurrences involve vehicle operators deviating from a surface movement controller clearance. These "failure to comply" occurrences most usually involve vehicles:

  • using an incorrect taxiway
  • failing to stop at a taxiway holding point
  • failing to stay on the surface movement control radio frequency or ground frequency as appropriate
  • failing to obtain a clearance before entering an area subject to control.

In all cases, these actions have the potential to put the vehicle in conflict with an aircraft which, in turn, could:

  • lead to collision
  • require aggressive braking by the aircraft which could result in personnel injuries. Cabin crew are especially vulnerable as they might be moving within the cabin preforming pre-departure or post-landing duties


Most of the remaining occurrences are related to one of the following:

  • aircraft-aircraft collisions or near collisions - collisions can result from:
    • failure to follow taxiway centreline guidance
    • failure to stop prior to a stopbar
    • taxiing at speeds unsuited to the conditions or level of congestion
    • taxiway deviation whilst trying to manoeuvre to "squeeze" past another aircraft. Manoeuvring around an aircraft partially blocking a taxiway (as might be the case if the aircraft was approaching, but not yet at the stop point of, a gate) can lead to collision. If misjudged, this could result in a wingtip striking the tail of the stopped aircraft or it could compromise clearance between obstacles or other aircraft and the wingtip opposite the stopped aircraft
    • taxiway configuration - converging taxiways can potentially lead to reduced or compromised clearance, especially where they cross
  • reduced aircraft clearance with ground equipment or obstacles. Reduced clearance accidents or incidents can occur in various ways. These include:
    • inappropriate use of a restricted taxiway - some taxiways are restricted by wingspan. Use by a larger aircraft could compromise obstacle clearance
    • failure to follow taxi lane guidance - deviation from the lane guidance whilst manoeuvring in proximity to light stands, gates or stationary equipment can result in collision
  • jet blast -inappropriate thrust settings or following too closely can result in aircraft damage due to jet blast. Jet blast can also cause unsecured equipment such as Unit Load Devices (ULD) to move and strike other aircraft, equipment or personnel

Prevention

Most taxiway accidents and incidents are preventable. This prevention is dependant upon appropriate training and testing, compliance with clearances, published procedures and right-of-way rules, maintaining situational awareness and adapting speed of movement to suit the weather and surface conditions. Some specific accident prevention strategies are as follows:

  • Vehicle operators - It is imperative that vehicle operators be properly trained, tested and authorised for ramp and taxiway operations. Driving infractions should be investigated and additional training provided where appropriate. Multiple infractions should be considered grounds for suspension of airside driving privileges. Operators should:
    • ensure daily inspection for their vehicle is complete and that beacon/hazard lights are operating when the vehicle is airside
    • maintain situational awareness
    • operate their vehicle safely and in accordance with all company and airport rules
    • obey all "rules of the road" inclusive of speed limits, stop signs and right-of-way guidance
    • yield to aircraft at all times
    • obtain and read back any ground movement controller clearance prior to entering an area where clearance is required. If clearance is not understood, ASK!
  • Tug operators - Tug operators have the additional responsibility of moving aircraft on and off gates as well as positioning aircraft from one location on the airfield to another. In addition to the aforementioned items for vehicle operators, the tug operator must:
    • know the size of the aircraft in tow inclusive of the wingspan
    • be conversant with the normal taxi routes from one airfield location to another
    • understand the stopping distances required for a tug with an aircraft in tow
    • comply with all clearances, especially runway crossing clearances
    • use wing and tail walkers when manoeuvring in congested areas
  • Controllers - The ground controller is responsible for the safe and efficient movement of aircraft and vehicle traffic on the taxiways and aprons. They should:
    • provide the appropriate clearance for the requested action
    • ensure that the clearance readback is accurate
    • to the extent possible, monitor the movement visually or via transponder or multilateration equipment to ensure compliance with the clearance
  • Pilots -

Accidents and Incidents

The following accidents and incidents involve collision or near collision between two aircraft, an aircraft and a vehicle, or an aircraft and a stationary object.

Aircraft/Aircraft Conflict

  • MD82 / MD11, Anchorage AK USA, 2002 (On 17 March 2002, at Ted Stevens Anchorage Airport, a McDonnell Douglas MD82 operated by Alaska Airlines, on a night pushback in snow conditions collided with an inbound taxiing McDonnell Douglas MD-11. The MD82 suffered substantial rudder damage although the impacting MD11 winglet was undamaged.)
  • B190 / B737, Calgary Canada, 2014 (On 29 March 2014, a Beech 1900D being taxied by maintenance personnel at Calgary entered the active runway without clearance in good visibility at night as a Boeing 737-700 was taking off. The 737 passed safely overhead. The Investigation found that the taxiing aircraft had taken a route completely contrary to the accepted clearance and that the engineer on control of the aircraft had not received any relevant training. Although the airport had ASDE in operation, a transponder code was not issued to the taxiing aircraft as required and stop bar crossing detection was not enabled at the time.)
  • DH8D / B737, Winnipeg Canada, 2014 (On 4 August 2014, the crew of a DHC8-400 departing Winnipeg continued beyond the holding point to which they had been cleared to taxi as a B737 was about to land. ATC observed the daylight incursion visually and instructed the approaching aircraft to go around as the DHC8 stopped within the runway protected area but clear of the actual runway. The Investigation found that the surface marking of the holding point which had been crossed was "significantly degraded" and noted the daily airport inspections had failed to identify this.)
  • FA7X, London City UK, 2016 (On 24 November 2016, a Dassault Falcon 7X being marshalled into an unmarked parking position after arriving at London City Airport was inadvertently directed into a collision with another crewed but stationary aircraft which sustained significant damage. The Investigation found that the apron involved had been congested and that the aircraft was being marshalled in accordance with airport procedures with wing walker assistance but a sharp corrective turn which created a 'wing growth' effect created a collision risk that was signalled at the last minute and incorrectly so by the wing walker involved and was also not seen by the marshaller.)
  • CRJ7 / CRJ2, Charlotte NC USA, 2008 (On 28 June 2008, a Bombardier CRJ 700 operated by PSA Airlines, during daytime pushback collided with a stationary CRJ 200 of the same company at Douglas International Airport Charlotte, North Carolina.)
  • B763 / A320, Delhi India, 2017 (On 8 August 2017, a Boeing 767-300 departing Delhi was pushed back into a stationary and out of service Airbus A320 on the adjacent gate rendering both aircraft unfit for flight. The Investigation found that the A320 had been instructed to park on a stand that was supposed to be blocked, a procedural requirement if the adjacent stand is to be used by a wide body aircraft and although this error had been detected by the stand allocation system, the alert was not noticed, in part due to inappropriate configuration. It was also found that the pushback was commenced without wing walkers.)
  • B772 / A321, London Heathrow UK, 2007 (On 27 July 2007, a British Airways Boeing 777-200ER collided, during pushback, with a stationary Airbus A321-200. The A321 was awaiting activation of the electronic Stand Entry Guidance (SEG) and expecting entry to its designated gate.)
  • B738/B738, Girona Spain, 2010 (On 14 January 2010, two Ryanair Boeing 737-800 aircraft were operating scheduled passenger flights from Girona to Las Palmas and Turin respectively and had taxied from adjacent gates at Girona in normal day visibility in quick succession. The Turin-bound aircraft taxied first but because it was early at the holding point for its CTOT, the other aircraft was designated first for take off and during the overtaking manoeuvre in the holding area, the wing tip of the moving Las Palmas aircraft hit the horizontal stabiliser of the Turin bound aircraft causing minor and substantial damage to the respective aircraft. None of the respective 81 and 77 occupants were injured and both aircraft taxied back to their gates.)

Aircraft/Vehicle Conflict

  • Vehicle / PA31, Mackay SE Australia, 2008 (On 29 June 2012, a Piper PA31 taking off from runway 05 on a passenger charter flight just missed hitting an inspection vehicle which had entered the take off runway from an intersecting one contrary to ATC clearance. The overflying aircraft was estimated to have cleared the vehicle by approximately 20 feet and the pilot was unaware it had entered the active runway. The driver had been taking a mobile telephone call at the time and attributed the incursion to distraction. The breached clearance had been given and correctly read back approximately two minutes prior to the conflict occurring.)
  • Vehicle / B752, Dublin Ireland, 2009 (On 29 May 2009, a Boeing 757-200 being operated by UK Airline Thomson Airways on a passenger charter flight from Sharm-el-Sheikh, Egypt to Dublin and having just landed on runway 10 at destination at night in poor visibility overtook a small ride-on grass mower moving along the right hand side of the runway in approximate line with the aircraft’s right hand wing tip. The driver of the mower was unaware of the arriving aircraft until he heard it on the runway behind him. Prior to the landing, ATC had been informed that all grass-cutting equipment previously working on and around the runway had cleared it.)
  • B737, Gran Canaria Spain, 2016 (On 7 January 2016, a Boeing 737-700 was inadvertently cleared by ATC to take off on a closed runway. The take-off was commenced with a vehicle visible ahead at the runway edge. When ATC realised the situation, a 'stop' instruction was issued and the aircraft did so after travelling approximately 740 metres. Investigation attributed the controller error to "lost situational awareness". It also noted prior pilot and controller awareness that the runway used was closed and that the pilots had, on the basis of the take-off clearance crossed a lit red stop bar to enter the runway without explicit permission.)
  • B742, Stockholm Arlanda Sweden, 2007 (On 25 June 2007, a Boeing 747-200F being operated by Cathay Pacific on a scheduled cargo flight from Stockholm to Dubai had completed push back for departure in normal daylight visibility and the parking brakes had been set. The tow vehicle crew had disconnected the tow bar but before they and their vehicle had cleared the vicinity of the aircraft, it began to taxi and collided with the vehicle. The flight crew were unaware of this and continued taxiing for about 150 metres until the flight engineer noticed that the indications from one if the engines were abnormal and the aircraft was taxied back to the gate. The tow vehicle crew and the dispatcher had been able to run clear and were not injured physically injured although all three were identified as suffering minor injury (shock). The aircraft was “substantially damaged” and the tow vehicle was “damaged”.)
  • A320, London Heathrow UK, 2006 (On 26 June 2006, after an uneventful pre-flight pushback of a British Airways Airbus A320-200 at London Heathrow Airport, the aircraft started moving under its own power and, shortly afterwards, collided with the tractor that had just performed the pushback, damaging both the right engine and the tractor.)
  • E190 / Vehicle, Paris CDG France, 2014 (On 19 April 2014, an Embraer 190 collided with the tug which was attempting to begin a pull forward after departure pushback which, exceptionally for the terminal concerned, was prohibited for the gate involved. As a result, severe damage was caused to the lower fuselage. The Investigation found that the relevant instructions were properly documented but ignored when apron services requested a 'push-pull' to minimise departure delay for an adjacent aircraft. Previous similar events had occurred on the same gate and it was suspected that a lack of appreciation of the reasons why the manoeuvre used was prohibited may have been relevant.)
  • Vehicle / E190 / E121, Jersey Channel Islands, 2010 (On 1 June 2010, an Airport RFFS bird scaring vehicle entered the active runway at Jersey in LVP without clearance and remained there for approximately three minutes until ATC became aware. The subsequent Investigation found that the incursion had fortuitously occurred just after an ERJ 190 had landed and had been terminated just as another aircraft had commenced a go around after failure to acquire the prescribed visual reference required to continue to a landing. The context for the failure of the vehicle driver to follow existing procedures was found to be their inadequacy and appropriate changes were implemented.)
  • ATP, Jersey Channel Islands, 1998 (On 9 May 1998, a British Regional Airlines ATP was being pushed back for departure at Jersey in daylight whilst the engines were being started when an excessive engine power setting applied by the flight crew led to the failure of the towbar connection and then to one of the aircraft's carbon fibre propellers striking the tug. A non standard emergency evacuation followed. All aircraft occupants and ground crew were uninjured.)

Aircraft/Object Conflict

  • A342, Perth Australia, 2005 (On 24 April 2005, an Airbus A340-200 landed short of the temporarily displaced runway threshold at Perth in good daylight visibility despite their prior awareness that there was such a displacement. The Investigation concluded that the crew had failed to correctly identify the applicable threshold markings because the markings provided were insufficiently clear to them and probably also because of the inappropriately low intensity setting of the temporary PAPI. No other Serious Incidents were reported during the same period of runway works.)
  • B737, Amsterdam Netherlands, 2003 (n 22 December 2003, a Boeing 737-700 being operated by UK Operator Easyjet on a scheduled passenger flight from Amsterdam to London Gatwick was taxiing for departure at night in normal visibility and took a different route to that instructed by ATC. The alternative route was, unknown to the flight crew, covered with ice and as a consequence, an attempt to maintain directional control during a turn was unsuccessful and the aircraft left wing collided with a lamp-post. The collision seriously damaged the aircraft and the lamp post. One passenger sustained slight injuries because of the impact. The diagram below taken from the official investigation report shows the area where the collision occurred.)
  • RJ85, Helsinki Finland 2010 (On 12 June 2010, a requested 22R runway inspection at Helsinki in normal daylight visibility carried out after a severe engine failure during the take off roll had led an Avro RJ85 being operated by Finnish Airline Blue1 on a scheduled passenger flight to Copenhagen to reject that take off at high speed. This inspection had not detected significant debris deposited on the runway during the sudden and severe engine failure. Two passenger aircraft, one being operated by Finnair to Dubrovnik, Croatia and the other being operated by Swedish airline TUIfly Nordic to Rhodes, Greece then departed the same runway before a re-inspection disclosed the debris and it was removed. Neither of the aircraft which used the runway prior to debris removal were subsequently found to have suffered any damage but both were advised of the situation en route.)
  • B738, Djalaluddin Indonesia, 2013 (On 6 August 2013, a Boeing 737-800 encountered cows ahead on the runway after landing normally in daylight following an uneventful approach and was unable to avoid colliding with them at high speed and as a result departed the runway to the left. Parts of the airport perimeter fencing were found to have been either missing or inadequately maintained for a significant period prior to the accident despite the existence of an airport bird and animal hazard management plan. Corrective action was taken following the accident.)
  • A319, Ibiza Spain, 2016 (On 19 June 2016, an Airbus A320 failed to follow the clearly-specified and ground-marked self-positioning exit from a regularly used gate at Ibiza and its right wing tip collided with the airbridge, damaging both it and the aircraft. The Investigation found that the crew had attempted the necessary left turn using the Operator’s ‘One Engine Taxi Departure’ procedure using the left engine but then failed to follow the marked taxi guideline by a significant margin. It was noted that there had been no other such difficulties with the same departure in the previous four years it had been in use.)
  • B773, Lisbon Portugal, 2016 (On 13 January 2016 ice was found on the upper and lower wing surfaces of a Boeing 777-300ER about to depart in the late morning from Lisbon in CAVOK conditions and 10°C. As Lisbon had no de-ice facilities, it was towed to a location where the sun would melt the ice more quickly but during poorly-planned manoeuvring, one of the wingtips was damaged by contact with an obstruction. The Investigation attributed the ice which led to the problematic re-positioning to the operator’s policy of tankering most of the return fuel on the overnight inbound flight where it had become cold-soaked.)
  • B74S, Stockholm Arlanda Sweden, 2006 (On 11 December 2006, a Boeing 747SP being operated by Syrian Air on a scheduled passenger flight from Damascus to Stockholm was arriving on the designated parking gate at destination in normal visibility at night when it collided with the airbridge. None of the 116 occupants of the aircraft suffered any injury but the aircraft was “substantially damaged” and the airbridge was “damaged”.)
  • A346, Toulouse France, 2007 (During ground running of engines, the aircraft impacted a concrete wall at a ground speed of 30 kts following unintended movement and the aircraft was wrecked.)

Related Articles

Further Reading

[[Category:Ground Operations [[Category:Operational Issues