If you wish to contribute or participate in the discussions about articles you are invited to join SKYbrary as a registered user

 Actions

Taxiway Collisions

From SKYbrary Wiki

Revision as of 22:00, 30 May 2018 by Editor2 (talk | contribs) (Prevention)
Article Information
Category: Ground Operations Ground Operations
Content source: SKYbrary About SKYbrary
Content control: SKYbrary About SKYbrary
Ambox content.png
The present article is under construction.
Reader enquiries are welcome, contact the editor: editor@skybrary.aero.
Ambox content.png

Description

An airport is a complex interface between the air and the ground environments, where access must be controlled and separation between aircraft or between aircraft and vehicular traffic must be maintained and optimised. While most occurrences on airport aprons and taxiways do not have consequences in terms of loss of life, they are often associated with aircraft damage, delays to passengers and avoidable financial costs.

This article examines collisions and near collisions whilst aircraft are on the airport manoeuvring areas inclusive of taxiways and ramp areas. The article On-Gate Collisions provides insight into aircraft collisions occurring whilst on, entering or leaving an assigned gate.

Occurrences

As previously stated, to ensure efficient and safe airport ground operations, separation between aircraft or between aircraft and vehicular traffic must be maintained and optimised. On occasion, however, minimum separation, particularly aircraft/vehicle separation is compromised. Whilst all events do not result in collision with an aircraft, the majority of taxiway occurrences involve vehicle operators deviating from a surface movement controller clearance. These "failure to comply" occurrences most usually involve vehicles:

  • using an incorrect taxiway
  • failing to stop at a taxiway holding point
  • failing to stay on the surface movement control radio frequency or ground frequency as appropriate
  • failing to obtain a clearance before entering an area subject to control.

In all cases, these actions have the potential to put the vehicle in conflict with an aircraft which, in turn, could:

  • lead to collision
  • require aggressive braking by the aircraft which could result in personnel injuries. Cabin crew are especially vulnerable as they might be moving within the cabin preforming pre-departure or post-landing duties


Most of the remaining occurrences are related to one of the following:

  • aircraft-aircraft collisions or near collisions - collisions can result from:
    • failure to follow taxiway centreline guidance
    • failure to stop prior to a stopbar
    • taxiing at speeds unsuited to the conditions or level of congestion
    • taxiway deviation whilst trying to manoeuvre to "squeeze" past another aircraft. Manoeuvring around an aircraft partially blocking a taxiway (as might be the case if the aircraft was approaching, but not yet at the stop point of, a gate) can lead to collision. If misjudged, this could result in a wingtip striking the tail of the stopped aircraft or it could compromise clearance between obstacles or other aircraft and the wingtip opposite the stopped aircraft
    • taxiway configuration - converging taxiways can potentially lead to reduced or compromised clearance, especially where they cross
  • reduced aircraft clearance with ground equipment or obstacles. Reduced clearance accidents or incidents can occur in various ways. These include:
    • inappropriate use of a restricted taxiway - some taxiways are restricted by wingspan. Use by a larger aircraft could compromise obstacle clearance
    • failure to follow taxi lane guidance - deviation from the lane guidance whilst manoeuvring in proximity to light stands, gates or stationary equipment can result in collision
  • jet blast -inappropriate thrust settings or following too closely can result in aircraft damage due to jet blast. Jet blast can also cause unsecured equipment such as Unit Load Devices (ULD) to move and strike other aircraft, equipment or personnel

Prevention

Most taxiway accidents and incidents are preventable. This prevention is dependant upon appropriate training and testing, compliance with clearances, published procedures and right-of-way rules, maintaining situational awareness and adapting speed of movement to suit the weather and surface conditions. Some specific accident prevention strategies are as follows:

  • Vehicle operators - It is imperative that vehicle operators be properly trained, tested and authorised for ramp and taxiway operations. Infractions should be investigated and additional training provided where appropriate. Multiple infractions should be considered grounds for suspension of airside driving privileges. Operators should:
    • ensure daily inspection for their vehicle is complete and that beacon/hazard lights are operating when the vehicle is airside
    • maintain situational awareness
    • operate their vehicle safely and in accordance with airport rules
    • obey all "rules of the road" inclusive of speed limits, stop signs and right-of-way guidance
    • yield to aircraft at all times
    • obtain and read back any ground movement controller clearance prior to entering an area where clearance is required
  • Tow crews -
  • Controllers -
  • Pilots -

Accidents and Incidents

The following accidents and incidents involve collision or near collision between two aircraft, an aircraft and a vehicle, or an aircraft and a stationary object.

Aircraft/Aircraft Conflict

  • DC91 / B722, Detroit MI USA, 1990 (On 3 December 1990 a Douglas DC9-10 flight crew taxiing for departure at Detroit in thick fog got lost and ended up stopped to one side of an active runway where, shortly after reporting their position, their aircraft was hit by a departing Boeing 727-200 and destroyed by the impact and subsequent fire. The Investigation concluded that the DC9 crew had failed to communicate positional uncertainty quickly enough but that their difficulties had been compounded by deficiencies in both the standard of air traffic service and airport surface markings, signage and lighting undetected by safety regulator oversight.)
  • MD82 / C441, Lambert-St Louis MI USA, 1994 (On 22 November 1994 a McDonnell Douglas MD 82 flight crew taking off from Lambert- St. Louis at night in excellent visibility suddenly became aware of a stationary Cessna 441 on the runway ahead and was unable to avoid a high speed collision. The collision destroyed the Cessna but allowed the MD82 to be brought to a controlled stop without occupant injury. The Investigation found that the Cessna 441 pilot had mistakenly believed his departure would be from the runway he had recently landed on and had entered that runway without clearance whilst still on GND frequency.)
  • B763 / A320, Delhi India, 2017 (On 8 August 2017, a Boeing 767-300 departing Delhi was pushed back into a stationary and out of service Airbus A320 on the adjacent gate rendering both aircraft unfit for flight. The Investigation found that the A320 had been instructed to park on a stand that was supposed to be blocked, a procedural requirement if the adjacent stand is to be used by a wide body aircraft and although this error had been detected by the stand allocation system, the alert was not noticed, in part due to inappropriate configuration. It was also found that the pushback was commenced without wing walkers.)
  • CRJ7 / CRJ2, Charlotte NC USA, 2008 (On 28 June 2008, a Bombardier CRJ 700 operated by PSA Airlines, during daytime pushback collided with a stationary CRJ 200 of the same company at Douglas International Airport Charlotte, North Carolina.)
  • B738/B763, Barcelona Spain, 2011 (On 14 April 2011, a Ryanair Boeing 737-800 failed to leave sufficient clearance when taxiing behind a stationary Boeing 767-300 at Barcelona and the 737 wingtip was in collision with the horizontal stabiliser of the 767, damaging both. The 767 crew were completely unaware of any impact but the 737 crew realised the ‘close proximity’ but dismissed a cabin crew report that a passenger had observed a collision. Both aircraft completed their intended flights without incident after which the damage was discovered, that to the 767 requiring that the aircraft be repaired before further flight.)
  • B744 / A321, London Heathrow UK, 2004 (On 23 March 2004, an out of service British Airways Boeing 747-400, under tow passed behind a stationary Airbus A321-200 being operated by Irish Airline Aer Lingus on a departing scheduled passenger service in good daylight visibility and the wing tip of the 747 impacted and seriously damaged the rudder of the A321. The aircraft under tow was cleared for the towing movement and the A321 was holding position in accordance with clearance. The towing team were not aware of the collision and initially, there was some doubt in the A321 flight deck about the cause of a ‘shudder’ felt when the impact occurred but the cabin crew of the A321 had felt the impact shudder and upon noticing the nose of the 747 appearing concluded that it had struck their aircraft. Then the First Officer saw the damaged wing tip of the 747 and informed ATC about the possible impact. Later another aircraft, positioned behind the A321, confirmed the rudder damage. At the time of the collision, the two aircraft involved were on different ATC frequencies.)
  • A321 / B734, Barcelona Spain, 2015 (On 25 November 2015, an Airbus A321 taxiing for departure at Barcelona was cleared across an active runway in front of an approaching Boeing 737 with landing clearance on the same runway by a Ground Controller unaware that the runway was active. On reaching the lit stop bar protecting the runway, the crew queried their clearance and were told to hold position. Noting that the event had occurred at the time of a routine twice-daily runway configuration change and two previous very similar events in 2012 and 2014, further safety recommendations on risk management of runway configuration change were made.)
  • A343 / B752, London Heathrow UK, 1995 (On 23 November 1995, in normal daylight visibility, an Airbus A340-300 being operated by Gulf Air on a scheduled international passenger flight from London Heathrow taxied past a Boeing 757-200 being operated by British Airways on a scheduled domestic passenger flight and also departing from London Heathrow which had stopped on a diverging taxiway within the departure holding area for Runway 27R such that the wing tip of the Airbus impacted the tail fin of other aircraft. Two of the 378 occupants of the two aircraft suffered minor injuries and both aircraft were damaged. Passengers were deplaned uneventfully from both aircraft.)

Aircraft/Vehicle Conflict

  • Vehicle / E190 / E121, Jersey Channel Islands, 2010 (On 1 June 2010, an Airport RFFS bird scaring vehicle entered the active runway at Jersey in LVP without clearance and remained there for approximately three minutes until ATC became aware. The subsequent Investigation found that the incursion had fortuitously occurred just after an ERJ 190 had landed and had been terminated just as another aircraft had commenced a go around after failure to acquire the prescribed visual reference required to continue to a landing. The context for the failure of the vehicle driver to follow existing procedures was found to be their inadequacy and appropriate changes were implemented.)
  • SB20, Stockholm Arlanda, 2001 (On 18 December 2001, a Saab 2000 being operated by Air Botnia on scheduled passenger flight from Stockholm to Oulu was taxiing out at night in normal visibility in accordance with its ATC clearance when a car appeared from the left on a roadway and drove at speed on a collision course with the aircraft. In order to avoid a collision, the aircraft had to brake sharply and the aircraft commander saw the car pass under the nose of the aircraft and judged the vehicle’s closest distance to the aircraft to be four to five metres. The car did not stop, could not subsequently be identified and no report was made by the driver or other witnesses. The diagram below taken from the official report shows the site of the conflict - the aircraft was emerging from Ramp ‘G’ to turn left on taxiway ‘Z’ and the broken line shows the roadway which is crossed just before the left turn is commenced.)
  • A320, London Heathrow UK, 2006 (On 26 June 2006, after an uneventful pre-flight pushback of a British Airways Airbus A320-200 at London Heathrow Airport, the aircraft started moving under its own power and, shortly afterwards, collided with the tractor that had just performed the pushback, damaging both the right engine and the tractor.)
  • B737, Gran Canaria Spain, 2016 (On 7 January 2016, a Boeing 737-700 was inadvertently cleared by ATC to take off on a closed runway. The take-off was commenced with a vehicle visible ahead at the runway edge. When ATC realised the situation, a 'stop' instruction was issued and the aircraft did so after travelling approximately 740 metres. Investigation attributed the controller error to "lost situational awareness". It also noted prior pilot and controller awareness that the runway used was closed and that the pilots had, on the basis of the take-off clearance crossed a lit red stop bar to enter the runway without explicit permission.)
  • Vehicle / B752, Dublin Ireland, 2009 (On 29 May 2009, a Boeing 757-200 being operated by UK Airline Thomson Airways on a passenger charter flight from Sharm-el-Sheikh, Egypt to Dublin and having just landed on runway 10 at destination at night in poor visibility overtook a small ride-on grass mower moving along the right hand side of the runway in approximate line with the aircraft’s right hand wing tip. The driver of the mower was unaware of the arriving aircraft until he heard it on the runway behind him. Prior to the landing, ATC had been informed that all grass-cutting equipment previously working on and around the runway had cleared it.)
  • B742, Stockholm Arlanda Sweden, 2007 (On 25 June 2007, a Boeing 747-200F being operated by Cathay Pacific on a scheduled cargo flight from Stockholm to Dubai had completed push back for departure in normal daylight visibility and the parking brakes had been set. The tow vehicle crew had disconnected the tow bar but before they and their vehicle had cleared the vicinity of the aircraft, it began to taxi and collided with the vehicle. The flight crew were unaware of this and continued taxiing for about 150 metres until the flight engineer noticed that the indications from one if the engines were abnormal and the aircraft was taxied back to the gate. The tow vehicle crew and the dispatcher had been able to run clear and were not injured physically injured although all three were identified as suffering minor injury (shock). The aircraft was “substantially damaged” and the tow vehicle was “damaged”.)
  • B738, London Stansted UK, 2008 (On 13 November 2008, a Boeing 737-800 with an unserviceable APU was being operated by Ryanair on a passenger flight at night was in collision with a tug after a cross-bleed engine start procedure was initiated prior to the completion of a complex aircraft pushback in rain. As the power was increased on the No 1 engine in preparation for the No 2 engine start, the resulting increase in thrust was greater than the counter-force provided by the tug and the aircraft started to move forwards. The towbar attachment failed and subsequently the aircraft’s No 1 engine impacted the side of the tug, prior to the aircraft brakes being applied.)
  • E190 / Vehicle, Paris CDG France, 2014 (On 19 April 2014, an Embraer 190 collided with the tug which was attempting to begin a pull forward after departure pushback which, exceptionally for the terminal concerned, was prohibited for the gate involved. As a result, severe damage was caused to the lower fuselage. The Investigation found that the relevant instructions were properly documented but ignored when apron services requested a 'push-pull' to minimise departure delay for an adjacent aircraft. Previous similar events had occurred on the same gate and it was suspected that a lack of appreciation of the reasons why the manoeuvre used was prohibited may have been relevant.)

Aircraft/Object Conflict

  • A342, Perth Australia, 2005 (On 24 April 2005, an Airbus A340-200 landed short of the temporarily displaced runway threshold at Perth in good daylight visibility despite their prior awareness that there was such a displacement. The Investigation concluded that the crew had failed to correctly identify the applicable threshold markings because the markings provided were insufficiently clear to them and probably also because of the inappropriately low intensity setting of the temporary PAPI. No other Serious Incidents were reported during the same period of runway works.)
  • B737, Amsterdam Netherlands, 2003 (n 22 December 2003, a Boeing 737-700 being operated by UK Operator Easyjet on a scheduled passenger flight from Amsterdam to London Gatwick was taxiing for departure at night in normal visibility and took a different route to that instructed by ATC. The alternative route was, unknown to the flight crew, covered with ice and as a consequence, an attempt to maintain directional control during a turn was unsuccessful and the aircraft left wing collided with a lamp-post. The collision seriously damaged the aircraft and the lamp post. One passenger sustained slight injuries because of the impact. The diagram below taken from the official investigation report shows the area where the collision occurred.)
  • B738, Djalaluddin Indonesia, 2013 (On 6 August 2013, a Boeing 737-800 encountered cows ahead on the runway after landing normally in daylight following an uneventful approach and was unable to avoid colliding with them at high speed and as a result departed the runway to the left. Parts of the airport perimeter fencing were found to have been either missing or inadequately maintained for a significant period prior to the accident despite the existence of an airport bird and animal hazard management plan. Corrective action was taken following the accident.)
  • B772, Singapore, 2013 (On 19 December 2013, the left engine of a Boeing 777-200 taxiing onto its assigned parking gate after arrival at Singapore ingested an empty cargo container resulting in damage to the engine which was serious enough to require its subsequent removal and replacement. The Investigation found that the aircraft docking guidance system had been in use despite the presence of the ingested container and other obstructions within the clearly marked 'equipment restraint area' of the gate involved. The corresponding ground handling procedures were found to be deficient as were those for ensuring general ramp awareness of a 'live' gate.)
  • B744, Johannesburg South Africa, 2013 (On 22 December 2013, a Boeing 747-400 taxiing for departure at Johannesburg at night with an augmented crew failed to follow its correctly-acknowledged taxi clearance and one wing hit a building resulting in substantial damage to both aircraft and building and a significant fuel leak. The aircraft occupants were all uninjured but four people in the building sustained minor injuries. The accident was attributed to crew error both in respect of an inadequate briefing and failure to monitor aircraft position using available charts and visual reference. Some minor contributory factors relating to the provision of airport lighting and signage were noted.)
  • DH8D, Hubli India, 2015 (On 8 March 2015, directional control of a Bombardier DHC 8-400 which had just completed a normal approach and landing was lost and the aircraft departed the side of the runway following the collapse of both the left main and nose landing gear assemblies. The Investigation found that after being allowed to drift to the side of the runway without corrective action, the previously airworthy aircraft had hit a non-frangible edge light and the left main gear and then the nose landing gear had collapsed with a complete loss of directional control. The aircraft had then exited the side of the runway sustaining further damage.)
  • A346, Toulouse France, 2007 (During ground running of engines, the aircraft impacted a concrete wall at a ground speed of 30 kts following unintended movement and the aircraft was wrecked.)
  • B74S, Stockholm Arlanda Sweden, 1996 (On 14 June 1996, a Boeing 747SP being operated by Air China on a scheduled passenger flight from Beijing to Stockholm was arriving on the designated parking gate at destination in normal daylight visibility when it collided with the airbridge. None of the 130 occupants of the aircraft suffered any injury but the aircraft was “substantially damaged” and the airbridge was “damaged”.)

Related Articles

Further Reading

[[Category:Ground Operations [[Category:Operational Issues