If you wish to contribute or participate in the discussions about articles you are invited to join SKYbrary as a registered user

 Actions

Difference between revisions of "Taxiway Collisions"

From SKYbrary Wiki

m (Accidents and Incidents)
 
(30 intermediate revisions by 2 users not shown)
Line 7: Line 7:
 
|control_caption  = About SKYbrary
 
|control_caption  = About SKYbrary
 
}}
 
}}
{{Under construction}}
+
 
 
==Description==
 
==Description==
 
An airport is a complex interface between the air and the ground environments, where  access must be controlled and separation between aircraft or between aircraft and vehicular traffic must be maintained and optimised. While most occurrences on airport aprons and taxiways do not have consequences in terms of loss of life, they are often associated with aircraft damage, delays to passengers and avoidable financial costs.
 
An airport is a complex interface between the air and the ground environments, where  access must be controlled and separation between aircraft or between aircraft and vehicular traffic must be maintained and optimised. While most occurrences on airport aprons and taxiways do not have consequences in terms of loss of life, they are often associated with aircraft damage, delays to passengers and avoidable financial costs.
Line 13: Line 13:
 
This article examines collisions and near collisions whilst aircraft are on the airport manoeuvring areas inclusive of taxiways and ramp areas. The article [[On-Gate Collisions]] provides insight into aircraft collisions occurring whilst on, entering or leaving an assigned gate.
 
This article examines collisions and near collisions whilst aircraft are on the airport manoeuvring areas inclusive of taxiways and ramp areas. The article [[On-Gate Collisions]] provides insight into aircraft collisions occurring whilst on, entering or leaving an assigned gate.
 
==Occurrences==
 
==Occurrences==
Whilst all events do not result in collision with an aircraft, the majority of taxiway occurrences involve vehicle operators deviating from a surface movement controller clearance. These "failure to comply" occurrences most usually involve vehicles:
+
As previously stated, to ensure efficient and safe airport ground operations, separation between aircraft or between aircraft and vehicular traffic must be maintained and optimised. On occasion, however, minimum separation, particularly aircraft/vehicle separation is compromised. Whilst all events do not result in collision with an aircraft, the majority of taxiway occurrences involve vehicle operators deviating from a surface movement controller clearance. These "failure to comply" occurrences most usually involve vehicles:
 
*using an incorrect taxiway
 
*using an incorrect taxiway
 
*failing to stop at a taxiway holding point
 
*failing to stop at a taxiway holding point
 
*failing to stay on the surface movement control radio frequency or ground frequency as appropriate
 
*failing to stay on the surface movement control radio frequency or ground frequency as appropriate
 
*failing to obtain a clearance before entering an area subject to control.
 
*failing to obtain a clearance before entering an area subject to control.
 
  
 
In all cases, these actions have the potential to put the vehicle in conflict with an aircraft which, in turn, could:
 
In all cases, these actions have the potential to put the vehicle in conflict with an aircraft which, in turn, could:
Line 26: Line 25:
  
 
Most of the remaining occurrences are related to one of the following:
 
Most of the remaining occurrences are related to one of the following:
 +
*aircraft-aircraft collisions or near collisions - collisions can result from:
 +
**failure to follow taxiway centreline guidance
 +
**failure to stop prior to a [[Stopbars (SKYclip)|stopbar]]
 +
**taxiing at speeds unsuited to the conditions or level of congestion
 +
**taxiway deviation whilst trying to manoeuvre to "squeeze" past another aircraft. Manoeuvring around an aircraft partially blocking a taxiway (as might be the case if the aircraft was approaching, but not yet at the stop point of, a gate) can lead to collision. If misjudged, this could result in a wingtip striking the tail of the stopped aircraft or it could compromise clearance between obstacles or other aircraft and the wingtip opposite the stopped aircraft
 +
**taxiway configuration - converging taxiways can potentially lead to reduced or compromised clearance, especially where they cross
 
*reduced aircraft clearance with ground equipment or obstacles. Reduced clearance accidents or incidents can occur in various ways. These include:
 
*reduced aircraft clearance with ground equipment or obstacles. Reduced clearance accidents or incidents can occur in various ways. These include:
 
**inappropriate use of a restricted taxiway - some taxiways are restricted by wingspan. Use by a larger aircraft could compromise obstacle clearance
 
**inappropriate use of a restricted taxiway - some taxiways are restricted by wingspan. Use by a larger aircraft could compromise obstacle clearance
**manoeuvring around an aircraft partially blocking a taxiway (as might be the case if the aircraft was approaching, but not yet at the stop point of, a gate). If misjudged, this could result in a wingtip striking the tail of the stopped aircraft or it could compromise clearance between obstacles or other aircraft and the wingtip opposite the stopped aircraft
+
**failure to follow taxi lane guidance - deviation from the lane guidance whilst manoeuvring in proximity to light stands, gates or stationary equipment can result in collision
*aircraft-aircraft collisions or near collisions - collisions can result from:
+
*jet blast -inappropriate thrust settings or following too closely can result in aircraft damage due to [[Jet Efflux Hazard|jet blast]]. Jet blast can also cause unsecured equipment such as [[Unit Load Devices]] to move and strike other aircraft, equipment or personnel
**failure to follow taxiway centreline guidance
+
 
**failure to stop prior to a stop bar
+
==Prevention==
**taxiing at speeds unsuited to the conditions or congestion
+
Most taxiway accidents and incidents are preventable. This prevention is dependant upon appropriate training and testing, compliance with clearances, published procedures and right-of-way rules, maintaining situational awareness and adapting speed of movement to suit the weather and surface conditions. Some specific accident prevention strategies are as follows:
**taxiway deviation whilst trying to manoeuvre to "squeeze" past another aircraft
+
*Vehicle operators - It is imperative that vehicle operators be properly trained, tested and authorised for ramp and taxiway operations. Driving infractions should be investigated and additional training provided where appropriate. Multiple infractions should be considered grounds for suspension of airside driving privileges. Operators should:
*jet blast -inappropriate thrust settings or following too closely can result in aircraft damage due to jet blast. Jet blast can also cause unsecured equipment such as ULDs to move and strike other aircraft, equipment or personnel
+
**ensure daily inspection for their vehicle is complete and that beacon/hazard lights are operating when the vehicle is airside
 +
**maintain situational awareness
 +
**operate their vehicle safely and in accordance with all company and airport rules
 +
**obey all "rules of the road" inclusive of speed limits, stop signs and right-of-way guidance
 +
**yield to aircraft at all times
 +
**obtain and read back any ground movement controller clearance prior to entering an area where clearance is required. If clearance is not understood, ASK!
 +
*Tug operators - Tug operators have the additional responsibility of moving aircraft on and off gates as well as positioning aircraft from one location on the airfield to another. In addition to the aforementioned items for vehicle operators, the tug operator must:
 +
**know the size of the aircraft in tow inclusive of the wingspan
 +
**be conversant with the normal taxi routes from one airfield location to another
 +
**understand the stopping distances required for a tug with an aircraft in tow
 +
**comply with all clearances, especially runway crossing clearances
 +
**use wing and tail walkers when manoeuvring in congested areas
 +
*Controllers - The ground controller is responsible for the safe and efficient movement of aircraft and vehicle traffic on the taxiways and aprons. They should:
 +
**provide the appropriate clearance for the requested action
 +
**ensure that the clearance readback is accurate
 +
**to the extent possible, monitor the movement visually, via transponder or by use of [[Multilateration|multilateration equipment]] to ensure clearance compliance
 +
*Pilots - In general, pilots are responsible for the ground movement of an aircraft from the runway to the gate and from the gate to the runway although they may also reposition aircraft from one point on the airfield to another. In all cases they should:
 +
**request, readback and comply with an appropriate clearance
 +
**maintain situational awareness
 +
**taxi at a speed appropriate to the conditions and traffic situation
 +
**maintain the centre of the taxi lane
 +
**be vigilant for taxi lane compromise by another aircraft, vehicle or object
 +
**not assume that vehicles will yield right-of-way
 +
 
 
==Accidents and Incidents==
 
==Accidents and Incidents==
[[B738 / B738, Dublin Ireland, 2014]] (On 7 October 2014, a locally-based Boeing 737-800 taxiing for departure from runway 34 at Dublin as cleared in normal night visibility collided with another 737-800 stationary in a queue awaiting departure from runway 28. Whilst accepting that pilots have sole responsible for collision avoidance, the Investigation found that relevant restrictions on taxi clearances were being routinely ignored by ATC. It also noted that visual judgement of wingtip clearance beyond 10 metres was problematic and that a subsequent very similar event at Dublin involving two 737-800s of the same Operator was the subject of a separate investigation.)
+
The following accidents and incidents involve collision or near collision between two aircraft, an aircraft and a vehicle, or an aircraft and a stationary object.
[[B738 / B738, Seville Spain, 2012]]
+
===Aircraft/Aircraft Conflict===
 
+
{{#ask: [[GND::Aircraft / Aircraft conflict]]
{{#ask: [[Category:Accidents and Incidents]][[Phase of Flight::Taxi]][[Event Type::GND:Aircraft-aircraft collision]]
+
|?Synopsis=
 +
|format=ul
 +
|order=random
 +
|limit=8
 +
|searchlabel=
 +
}}
 +
===Aircraft/Vehicle Conflict===
 +
{{#ask: [[GND::Aircraft / Vehicle conflict]]
 +
|?Synopsis=
 +
|format=ul
 +
|order=random
 +
|limit=8
 +
|searchlabel=
 +
}}
 +
===Aircraft/Object Conflict===
 +
{{#ask: [[GND::Aircraft / Object or Structure conflict]]
 
|?Synopsis=
 
|?Synopsis=
 
|format=ul
 
|format=ul
|limit=5
+
|order=random
 +
|limit=8
 +
|searchlabel=
 
}}
 
}}
  
Line 58: Line 103:
 
*[http://www.skybrary.aero/bookshelf/books/3524.pdf ACRP Report 148: LED Airfield Lighting System Operation and Maintenance], J. Burns et al., Transportation Research Board (U.S.), 2015
 
*[http://www.skybrary.aero/bookshelf/books/3524.pdf ACRP Report 148: LED Airfield Lighting System Operation and Maintenance], J. Burns et al., Transportation Research Board (U.S.), 2015
  
[[Category:Ground Operations   [[Category:Operational Issues
+
[[Category:Ground Operations]]

Latest revision as of 10:02, 28 June 2018

Article Information
Category: Ground Operations Ground Operations
Content source: SKYbrary About SKYbrary
Content control: SKYbrary About SKYbrary

Description

An airport is a complex interface between the air and the ground environments, where access must be controlled and separation between aircraft or between aircraft and vehicular traffic must be maintained and optimised. While most occurrences on airport aprons and taxiways do not have consequences in terms of loss of life, they are often associated with aircraft damage, delays to passengers and avoidable financial costs.

This article examines collisions and near collisions whilst aircraft are on the airport manoeuvring areas inclusive of taxiways and ramp areas. The article On-Gate Collisions provides insight into aircraft collisions occurring whilst on, entering or leaving an assigned gate.

Occurrences

As previously stated, to ensure efficient and safe airport ground operations, separation between aircraft or between aircraft and vehicular traffic must be maintained and optimised. On occasion, however, minimum separation, particularly aircraft/vehicle separation is compromised. Whilst all events do not result in collision with an aircraft, the majority of taxiway occurrences involve vehicle operators deviating from a surface movement controller clearance. These "failure to comply" occurrences most usually involve vehicles:

  • using an incorrect taxiway
  • failing to stop at a taxiway holding point
  • failing to stay on the surface movement control radio frequency or ground frequency as appropriate
  • failing to obtain a clearance before entering an area subject to control.

In all cases, these actions have the potential to put the vehicle in conflict with an aircraft which, in turn, could:

  • lead to collision
  • require aggressive braking by the aircraft which could result in personnel injuries. Cabin crew are especially vulnerable as they might be moving within the cabin preforming pre-departure or post-landing duties


Most of the remaining occurrences are related to one of the following:

  • aircraft-aircraft collisions or near collisions - collisions can result from:
    • failure to follow taxiway centreline guidance
    • failure to stop prior to a stopbar
    • taxiing at speeds unsuited to the conditions or level of congestion
    • taxiway deviation whilst trying to manoeuvre to "squeeze" past another aircraft. Manoeuvring around an aircraft partially blocking a taxiway (as might be the case if the aircraft was approaching, but not yet at the stop point of, a gate) can lead to collision. If misjudged, this could result in a wingtip striking the tail of the stopped aircraft or it could compromise clearance between obstacles or other aircraft and the wingtip opposite the stopped aircraft
    • taxiway configuration - converging taxiways can potentially lead to reduced or compromised clearance, especially where they cross
  • reduced aircraft clearance with ground equipment or obstacles. Reduced clearance accidents or incidents can occur in various ways. These include:
    • inappropriate use of a restricted taxiway - some taxiways are restricted by wingspan. Use by a larger aircraft could compromise obstacle clearance
    • failure to follow taxi lane guidance - deviation from the lane guidance whilst manoeuvring in proximity to light stands, gates or stationary equipment can result in collision
  • jet blast -inappropriate thrust settings or following too closely can result in aircraft damage due to jet blast. Jet blast can also cause unsecured equipment such as Unit Load Devices (ULD) to move and strike other aircraft, equipment or personnel

Prevention

Most taxiway accidents and incidents are preventable. This prevention is dependant upon appropriate training and testing, compliance with clearances, published procedures and right-of-way rules, maintaining situational awareness and adapting speed of movement to suit the weather and surface conditions. Some specific accident prevention strategies are as follows:

  • Vehicle operators - It is imperative that vehicle operators be properly trained, tested and authorised for ramp and taxiway operations. Driving infractions should be investigated and additional training provided where appropriate. Multiple infractions should be considered grounds for suspension of airside driving privileges. Operators should:
    • ensure daily inspection for their vehicle is complete and that beacon/hazard lights are operating when the vehicle is airside
    • maintain situational awareness
    • operate their vehicle safely and in accordance with all company and airport rules
    • obey all "rules of the road" inclusive of speed limits, stop signs and right-of-way guidance
    • yield to aircraft at all times
    • obtain and read back any ground movement controller clearance prior to entering an area where clearance is required. If clearance is not understood, ASK!
  • Tug operators - Tug operators have the additional responsibility of moving aircraft on and off gates as well as positioning aircraft from one location on the airfield to another. In addition to the aforementioned items for vehicle operators, the tug operator must:
    • know the size of the aircraft in tow inclusive of the wingspan
    • be conversant with the normal taxi routes from one airfield location to another
    • understand the stopping distances required for a tug with an aircraft in tow
    • comply with all clearances, especially runway crossing clearances
    • use wing and tail walkers when manoeuvring in congested areas
  • Controllers - The ground controller is responsible for the safe and efficient movement of aircraft and vehicle traffic on the taxiways and aprons. They should:
    • provide the appropriate clearance for the requested action
    • ensure that the clearance readback is accurate
    • to the extent possible, monitor the movement visually, via transponder or by use of multilateration equipment to ensure clearance compliance
  • Pilots - In general, pilots are responsible for the ground movement of an aircraft from the runway to the gate and from the gate to the runway although they may also reposition aircraft from one point on the airfield to another. In all cases they should:
    • request, readback and comply with an appropriate clearance
    • maintain situational awareness
    • taxi at a speed appropriate to the conditions and traffic situation
    • maintain the centre of the taxi lane
    • be vigilant for taxi lane compromise by another aircraft, vehicle or object
    • not assume that vehicles will yield right-of-way

Accidents and Incidents

The following accidents and incidents involve collision or near collision between two aircraft, an aircraft and a vehicle, or an aircraft and a stationary object.

Aircraft/Aircraft Conflict

  • DH8D / B737, Winnipeg Canada, 2014 (On 4 August 2014, the crew of a DHC8-400 departing Winnipeg continued beyond the holding point to which they had been cleared to taxi as a B737 was about to land. ATC observed the daylight incursion visually and instructed the approaching aircraft to go around as the DHC8 stopped within the runway protected area but clear of the actual runway. The Investigation found that the surface marking of the holding point which had been crossed was "significantly degraded" and noted the daily airport inspections had failed to identify this.)
  • FA7X, London City UK, 2016 (On 24 November 2016, a Dassault Falcon 7X being marshalled into an unmarked parking position after arriving at London City Airport was inadvertently directed into a collision with another crewed but stationary aircraft which sustained significant damage. The Investigation found that the apron involved had been congested and that the aircraft was being marshalled in accordance with airport procedures with wing walker assistance but a sharp corrective turn which created a 'wing growth' effect created a collision risk that was signalled at the last minute and incorrectly so by the wing walker involved and was also not seen by the marshaller.)
  • B738/A321, Prague Czech Republic, 2010 (On 18 June 2010 a Sun Express Boeing 737-800 taxiing for a full length daylight departure from runway 06 at Prague was in collision with an Airbus 321 which was waiting on a link taxiway leading to an intermediate take off position on the same runway. The aircraft sustained damage to their right winglet and left horizontal stabiliser respectively and both needed subsequent repair before being released to service.)
  • RJ85 / RJ1H, London City Airport, London UK, 2008 (On 21 April 2008, an Avro RJ85 aircraft was parked on Stand 10 at London City Airport, with an Avro RJ100 parked to its left, on the adjacent Stand 11. After being repositioned by a tug, the RJ85 taxied forward and to the right, its tail contacting the tail of the RJ100 and causing minor damage to the RJ100’s right elevator.)
  • A343 / B744, London Heathrow UK, 2007 (On 15 October 2007, an Airbus 340-300 being operated on a scheduled passenger flight by Air Lanka with a heavy crew in the flight deck was taxiing towards the departure runway at London Heathrow at night in normal visibility when the right wing tip hit and sheared off the left hand winglet of a stationary British Airways Boeing 747-400 which was in a queue on an adjacent taxiway. The Airbus 340 sustained only minor damage to the right winglet and navigation light.)
  • CRJ7 / CRJ2, Charlotte NC USA, 2008 (On 28 June 2008, a Bombardier CRJ 700 operated by PSA Airlines, during daytime pushback collided with a stationary CRJ 200 of the same company at Douglas International Airport Charlotte, North Carolina.)
  • B190 / B737, Calgary Canada, 2014 (On 29 March 2014, a Beech 1900D being taxied by maintenance personnel at Calgary entered the active runway without clearance in good visibility at night as a Boeing 737-700 was taking off. The 737 passed safely overhead. The Investigation found that the taxiing aircraft had taken a route completely contrary to the accepted clearance and that the engineer on control of the aircraft had not received any relevant training. Although the airport had ASDE in operation, a transponder code was not issued to the taxiing aircraft as required and stop bar crossing detection was not enabled at the time.)
  • B742 / B741, Tenerife Canary Islands Spain, 1977 (On 27 March 1977, a KLM Boeing 747-200 began its low visibility take-off at Tenerife without requesting or receiving take-off clearance and a collision with a Boeing 747-100 backtracking the same runway subsequently occurred. Both aircraft were destroyed by the impact and consequential fire and 583 people died. The Investigation attributed the crash primarily to the actions and inactions of the KLM Captain, who was the Operator's Chief Flying Instructor. Safety Recommendations made emphasised the importance of standard phraseology in all normal radio communications and avoidance of the phrase "take-off" in ATC Departure Clearances.)

Aircraft/Vehicle Conflict

  • B737, Gran Canaria Spain, 2016 (On 7 January 2016, a Boeing 737-700 was inadvertently cleared by ATC to take off on a closed runway. The take-off was commenced with a vehicle visible ahead at the runway edge. When ATC realised the situation, a 'stop' instruction was issued and the aircraft did so after travelling approximately 740 metres. Investigation attributed the controller error to "lost situational awareness". It also noted prior pilot and controller awareness that the runway used was closed and that the pilots had, on the basis of the take-off clearance crossed a lit red stop bar to enter the runway without explicit permission.)
  • A320, Dublin Ireland, 2017 (On 27 September 2017, an Airbus A320 being manoeuvred off the departure gate at Dublin by tug was being pulled forward when the tow bar shear pin broke and the tug driver lost control. The tug then collided with the right engine causing significant damage. The tug driver and assisting ground crew were not injured. The Investigation concluded that although the shear pin failure was not attributable to any particular cause, the relative severity of the outcome was probably increased by the wet surface, a forward slope on the ramp and fact that an engine start was in progress.)
  • B738, London Stansted UK, 2008 (On 13 November 2008, a Boeing 737-800 with an unserviceable APU was being operated by Ryanair on a passenger flight at night was in collision with a tug after a cross-bleed engine start procedure was initiated prior to the completion of a complex aircraft pushback in rain. As the power was increased on the No 1 engine in preparation for the No 2 engine start, the resulting increase in thrust was greater than the counter-force provided by the tug and the aircraft started to move forwards. The towbar attachment failed and subsequently the aircraft’s No 1 engine impacted the side of the tug, prior to the aircraft brakes being applied.)
  • B763, Luton UK, 2005 (On 16 February 2005, at Luton Airport, a Boeing B767-300 collided with the tug pulling it forward when the shear pin of the unserviceable tow bar being used to pull the aircraft broke. The aircraft ran onto the tug when the ground crew stopped the tug suddenly. As result of the collision with the tug the aircraft fuselage and landing gear was damaged.)
  • Vehicle / E190 / E121, Jersey Channel Islands, 2010 (On 1 June 2010, an Airport RFFS bird scaring vehicle entered the active runway at Jersey in LVP without clearance and remained there for approximately three minutes until ATC became aware. The subsequent Investigation found that the incursion had fortuitously occurred just after an ERJ 190 had landed and had been terminated just as another aircraft had commenced a go around after failure to acquire the prescribed visual reference required to continue to a landing. The context for the failure of the vehicle driver to follow existing procedures was found to be their inadequacy and appropriate changes were implemented.)
  • A343, Frankfurt Germany, 2008 (On 21 August 2008, an Airbus A340-300 being operated by an undisclosed operator by a German-licensed flight crew on a scheduled passenger flight from Teheran to Frankfurt collided with a stationary bus with only the driver on board whilst approaching the allocated parking gate in normal daylight visibility. The No 4 engine impacted the bus roof as shown in the photograph below reproduced from the official report. None of the occupants of either the aircraft or the bus were injured.)
  • FA50 / Vehicle, Moscow Vnukovo Russia, 2014 (On 20 October 2014 a Dassault Falcon 50 taking off at night from Moscow Vnukovo collided with a snow plough which had entered the same runway without clearance shortly after rotation. Control was lost and all occupants died when it was destroyed by impact forces and post crash fire. The uninjured snow plough driver was subsequently discovered to be under the influence of alcohol. The Investigation found that the A-SMGCS effective for over a year prior to the collision had not been properly configured nor had controllers been adequately trained on its use, especially its conflict alerting functions.)
  • SB20, Stockholm Arlanda, 2001 (On 18 December 2001, a Saab 2000 being operated by Air Botnia on scheduled passenger flight from Stockholm to Oulu was taxiing out at night in normal visibility in accordance with its ATC clearance when a car appeared from the left on a roadway and drove at speed on a collision course with the aircraft. In order to avoid a collision, the aircraft had to brake sharply and the aircraft commander saw the car pass under the nose of the aircraft and judged the vehicle’s closest distance to the aircraft to be four to five metres. The car did not stop, could not subsequently be identified and no report was made by the driver or other witnesses. The diagram below taken from the official report shows the site of the conflict - the aircraft was emerging from Ramp ‘G’ to turn left on taxiway ‘Z’ and the broken line shows the roadway which is crossed just before the left turn is commenced.)

Aircraft/Object Conflict

  • B773, Lisbon Portugal, 2016 (On 13 January 2016 ice was found on the upper and lower wing surfaces of a Boeing 777-300ER about to depart in the late morning from Lisbon in CAVOK conditions and 10°C. As Lisbon had no de-ice facilities, it was towed to a location where the sun would melt the ice more quickly but during poorly-planned manoeuvring, one of the wingtips was damaged by contact with an obstruction. The Investigation attributed the ice which led to the problematic re-positioning to the operator’s policy of tankering most of the return fuel on the overnight inbound flight where it had become cold-soaked.)
  • B734, Aberdeen UK, 2005 (Significant damage was caused to the tailplane and elevator of a Boeing 737-400 after the pavement beneath them broke up when take off thrust was applied for a standing start from the full length of the runway at Aberdeen. Although in this case neither outcome applied, the Investigation noted that control difficulties consequent upon such damage could lead to an overrun following a high speed rejected takeoff or to compromised flight path control airborne. Safety Recommendations on appropriate regulatory guidance for marking and construction of blast pads and on aircraft performance, rolling take offs and lead-on line marking were made.)
  • AT72, Shannon Ireland, 2014 (On 26 February 2014, an ATR 72-202 which had been substituted for the ATR42 which usually operated a series of night cargo flights was being marshalled out of its parking position with a new flight crew on board when the left wing was in collision with the structure of an adjacent hangar. The Investigation found that the aircraft type had not been changed on the applicable flight plan and ATC were consequently unaware that the aircraft had previously been parked in a position only approved for the use by the usual smaller aircraft type.)
  • A319, London Heathrow UK, 2007 (On 12 February 2007, an Airbus A319-100 being operated by British Airways on a scheduled passenger flight into London Heathrow made unintended contact in normal daylight visibility with the stationary airbridge at the arrival gate. This followed an emergency stop made after seeing hand signals from ground staff whilst following SEGS indications which appeared to suggest that there was a further 5 metres to run to the correct parking position. There was no damage to the aircraft, only minimal damage to the airbridge and there were no injuries to the aircraft occupants or any other person)
  • A320, Lisbon Portugal, 2015 (On 19 May 2015, an Airbus A319 crew attempted to taxi into a nose-in parking position at Lisbon despite the fact that the APIS, although switched on, was clearly malfunctioning whilst not displaying an unequivocal ‘STOP’. The aircraft continued 6 metres past the applicable apron ground marking by which time it had hit the airbridge. The marshaller in attendance to oversee the arrival did not signal the aircraft or manually select the APIS ‘STOP’ instruction. The APIS had failed to detect the dark-liveried aircraft and the non-display of a steady ‘STOP’ indication was independently attributed to a pre-existing system fault.)
  • A321, Daegu South Korea, 2006 (On 21 February 2006, an Airbus A321-200 being operated by China Eastern on a scheduled passenger flight from Daegu to Shanghai Pudong failed to follow the marked taxiway centreline when taxiing for departure in normal daylight visibility and a wing tip impacted an adjacent building causing minor damage to both building and aircraft. None of the 166 occupants were injured.)
  • B738, Barcelona Spain, 2015 (On 12 December 2015, whilst a Boeing 737-800 was beginning disembarkation of passengers via an air bridge which had just been attached on arrival at Barcelona, the bridge malfunctioned, raising the aircraft nose gear approximately 2 metres off the ground. The door attached to the bridge then failed and the aircraft dropped abruptly. Prompt cabin crew intervention prevented all but two minor injuries. The Investigation found that the occurrence had been made possible by the failure to recognise new functional risks created by a programme of partial renovation being carried out on the air bridges at the Terminal involved.)
  • A124, Zaragoza Spain, 2010 (On 20 April 2010, the left wing of an Antonov Design Bureau An124-100 which was taxiing in to park after a night landing at Zaragoza under marshalling guidance was in collision with two successive lighting towers on the apron. Both towers and the left wingtip of the aircraft were damaged. The subsequent investigation attributed the collision to allocation of an unsuitable stand and lack of appropriate guidance markings.)

Related Articles

Further Reading