If you wish to contribute or participate in the discussions about articles you are invited to join SKYbrary as a registered user

 Actions

Taxiway Collisions

From SKYbrary Wiki

Article Information
Category: Ground Operations Ground Operations
Content source: SKYbrary About SKYbrary
Content control: SKYbrary About SKYbrary

Description

An airport is a complex interface between the air and the ground environments, where access must be controlled and separation between aircraft or between aircraft and vehicular traffic must be maintained and optimised. While most occurrences on airport aprons and taxiways do not have consequences in terms of loss of life, they are often associated with aircraft damage, delays to passengers and avoidable financial costs.

This article examines collisions and near collisions whilst aircraft are on the airport manoeuvring areas inclusive of taxiways and ramp areas. The article On-Gate Collisions provides insight into aircraft collisions occurring whilst on, entering or leaving an assigned gate.

Occurrences

As previously stated, to ensure efficient and safe airport ground operations, separation between aircraft or between aircraft and vehicular traffic must be maintained and optimised. On occasion, however, minimum separation, particularly aircraft/vehicle separation is compromised. Whilst all events do not result in collision with an aircraft, the majority of taxiway occurrences involve vehicle operators deviating from a surface movement controller clearance. These "failure to comply" occurrences most usually involve vehicles:

  • using an incorrect taxiway
  • failing to stop at a taxiway holding point
  • failing to stay on the surface movement control radio frequency or ground frequency as appropriate
  • failing to obtain a clearance before entering an area subject to control.

In all cases, these actions have the potential to put the vehicle in conflict with an aircraft which, in turn, could:

  • lead to collision
  • require aggressive braking by the aircraft which could result in personnel injuries. Cabin crew are especially vulnerable as they might be moving within the cabin preforming pre-departure or post-landing duties


Most of the remaining occurrences are related to one of the following:

  • aircraft-aircraft collisions or near collisions - collisions can result from:
    • failure to follow taxiway centreline guidance
    • failure to stop prior to a stopbar
    • taxiing at speeds unsuited to the conditions or level of congestion
    • taxiway deviation whilst trying to manoeuvre to "squeeze" past another aircraft. Manoeuvring around an aircraft partially blocking a taxiway (as might be the case if the aircraft was approaching, but not yet at the stop point of, a gate) can lead to collision. If misjudged, this could result in a wingtip striking the tail of the stopped aircraft or it could compromise clearance between obstacles or other aircraft and the wingtip opposite the stopped aircraft
    • taxiway configuration - converging taxiways can potentially lead to reduced or compromised clearance, especially where they cross
  • reduced aircraft clearance with ground equipment or obstacles. Reduced clearance accidents or incidents can occur in various ways. These include:
    • inappropriate use of a restricted taxiway - some taxiways are restricted by wingspan. Use by a larger aircraft could compromise obstacle clearance
    • failure to follow taxi lane guidance - deviation from the lane guidance whilst manoeuvring in proximity to light stands, gates or stationary equipment can result in collision
  • jet blast -inappropriate thrust settings or following too closely can result in aircraft damage due to jet blast. Jet blast can also cause unsecured equipment such as Unit Load Devices (ULD) to move and strike other aircraft, equipment or personnel

Prevention

Most taxiway accidents and incidents are preventable. This prevention is dependant upon appropriate training and testing, compliance with clearances, published procedures and right-of-way rules, maintaining situational awareness and adapting speed of movement to suit the weather and surface conditions. Some specific accident prevention strategies are as follows:

  • Vehicle operators - It is imperative that vehicle operators be properly trained, tested and authorised for ramp and taxiway operations. Driving infractions should be investigated and additional training provided where appropriate. Multiple infractions should be considered grounds for suspension of airside driving privileges. Operators should:
    • ensure daily inspection for their vehicle is complete and that beacon/hazard lights are operating when the vehicle is airside
    • maintain situational awareness
    • operate their vehicle safely and in accordance with all company and airport rules
    • obey all "rules of the road" inclusive of speed limits, stop signs and right-of-way guidance
    • yield to aircraft at all times
    • obtain and read back any ground movement controller clearance prior to entering an area where clearance is required. If clearance is not understood, ASK!
  • Tug operators - Tug operators have the additional responsibility of moving aircraft on and off gates as well as positioning aircraft from one location on the airfield to another. In addition to the aforementioned items for vehicle operators, the tug operator must:
    • know the size of the aircraft in tow inclusive of the wingspan
    • be conversant with the normal taxi routes from one airfield location to another
    • understand the stopping distances required for a tug with an aircraft in tow
    • comply with all clearances, especially runway crossing clearances
    • use wing and tail walkers when manoeuvring in congested areas
  • Controllers - The ground controller is responsible for the safe and efficient movement of aircraft and vehicle traffic on the taxiways and aprons. They should:
    • provide the appropriate clearance for the requested action
    • ensure that the clearance readback is accurate
    • to the extent possible, monitor the movement visually, via transponder or by use of multilateration equipment to ensure clearance compliance
  • Pilots - In general, pilots are responsible for the ground movement of an aircraft from the runway to the gate and from the gate to the runway although they may also reposition aircraft from one point on the airfield to another. In all cases they should:
    • request, readback and comply with an appropriate clearance
    • maintain situational awareness
    • taxi at a speed appropriate to the conditions and traffic situation
    • maintain the centre of the taxi lane
    • be vigilant for taxi lane compromise by another aircraft, vehicle or object
    • not assume that vehicles will yield right-of-way

Accidents and Incidents

The following accidents and incidents involve collision or near collision between two aircraft, an aircraft and a vehicle, or an aircraft and a stationary object.

Aircraft/Aircraft Conflict

  • A319 / UNKN, Stockholm Arlanda Sweden, 2011 (On 5 February 2011, an Airbus A319-100 being operated by Air Berlin on a passenger flight departing Stockholm inadvertently proceeded beyond the given clearance limit for runway 19R and although it subsequently stopped before runway entry had occurred, it was by then closer to high speed departing traffic than it should have been. There was no abrupt stop and none of the 103 occupants were injured.)
  • MD82 / MD11, Anchorage AK USA, 2002 (On 17 March 2002, at Ted Stevens Anchorage Airport, a McDonnell Douglas MD82 operated by Alaska Airlines, on a night pushback in snow conditions collided with an inbound taxiing McDonnell Douglas MD-11. The MD82 suffered substantial rudder damage although the impacting MD11 winglet was undamaged.)
  • RJ85 / RJ1H, London City Airport, London UK, 2008 (On 21 April 2008, an Avro RJ85 aircraft was parked on Stand 10 at London City Airport, with an Avro RJ100 parked to its left, on the adjacent Stand 11. After being repositioned by a tug, the RJ85 taxied forward and to the right, its tail contacting the tail of the RJ100 and causing minor damage to the RJ100’s right elevator.)
  • B733 / DH8D, Fort McMurray Canada, 2014 (On 4 August 2014, a Boeing 737-300 making a day visual approach at Fort McMurray after receiving an ILS/DME clearance lined up on a recently-constructed parallel taxiway and its crew were only alerted to their error shortly before touchdown by the crew of a DHC8-400 which was taxiing along the same taxiway in the opposite direction. This resulted in a go around being commenced from 46 feet agl. The Investigation noted that both pilots had been looking out during the final stages of the approach and had ignored important SOPs including that for a mandatory go around from an unstable approach.)
  • DH8D / B737, Winnipeg Canada, 2014 (On 4 August 2014, the crew of a DHC8-400 departing Winnipeg continued beyond the holding point to which they had been cleared to taxi as a B737 was about to land. ATC observed the daylight incursion visually and instructed the approaching aircraft to go around as the DHC8 stopped within the runway protected area but clear of the actual runway. The Investigation found that the surface marking of the holding point which had been crossed was "significantly degraded" and noted the daily airport inspections had failed to identify this.)
  • A343 / B752, London Heathrow UK, 1995 (On 23 November 1995, in normal daylight visibility, an Airbus A340-300 being operated by Gulf Air on a scheduled international passenger flight from London Heathrow taxied past a Boeing 757-200 being operated by British Airways on a scheduled domestic passenger flight and also departing from London Heathrow which had stopped on a diverging taxiway within the departure holding area for Runway 27R such that the wing tip of the Airbus impacted the tail fin of other aircraft. Two of the 378 occupants of the two aircraft suffered minor injuries and both aircraft were damaged. Passengers were deplaned uneventfully from both aircraft.)
  • B742 / B741, Tenerife Canary Islands Spain, 1977 (On 27 March 1977, a KLM Boeing 747-200 began its low visibility take-off at Tenerife without requesting or receiving take-off clearance and a collision with a Boeing 747-100 backtracking the same runway subsequently occurred. Both aircraft were destroyed by the impact and consequential fire and 583 people died. The Investigation attributed the crash primarily to the actions and inactions of the KLM Captain, who was the Operator's Chief Flying Instructor. Safety Recommendations made emphasised the importance of standard phraseology in all normal radio communications and avoidance of the phrase "take-off" in ATC Departure Clearances.)
  • B190 / B737, Calgary Canada, 2014 (On 29 March 2014, a Beech 1900D being taxied by maintenance personnel at Calgary entered the active runway without clearance in good visibility at night as a Boeing 737-700 was taking off. The 737 passed safely overhead. The Investigation found that the taxiing aircraft had taken a route completely contrary to the accepted clearance and that the engineer on control of the aircraft had not received any relevant training. Although the airport had ASDE in operation, a transponder code was not issued to the taxiing aircraft as required and stop bar crossing detection was not enabled at the time.)

Aircraft/Vehicle Conflict

  • A320, Dublin Ireland, 2017 (On 27 September 2017, an Airbus A320 being manoeuvred off the departure gate at Dublin by tug was being pulled forward when the tow bar shear pin broke and the tug driver lost control. The tug then collided with the right engine causing significant damage. The tug driver and assisting ground crew were not injured. The Investigation concluded that although the shear pin failure was not attributable to any particular cause, the relative severity of the outcome was probably increased by the wet surface, a forward slope on the ramp and fact that an engine start was in progress.)
  • A320, London Heathrow UK, 2006 (On 26 June 2006, after an uneventful pre-flight pushback of a British Airways Airbus A320-200 at London Heathrow Airport, the aircraft started moving under its own power and, shortly afterwards, collided with the tractor that had just performed the pushback, damaging both the right engine and the tractor.)
  • B738, London Stansted UK, 2008 (On 13 November 2008, a Boeing 737-800 with an unserviceable APU was being operated by Ryanair on a passenger flight at night was in collision with a tug after a cross-bleed engine start procedure was initiated prior to the completion of a complex aircraft pushback in rain. As the power was increased on the No 1 engine in preparation for the No 2 engine start, the resulting increase in thrust was greater than the counter-force provided by the tug and the aircraft started to move forwards. The towbar attachment failed and subsequently the aircraft’s No 1 engine impacted the side of the tug, prior to the aircraft brakes being applied.)
  • B763, Luton UK, 2005 (On 16 February 2005, at Luton Airport, a Boeing B767-300 collided with the tug pulling it forward when the shear pin of the unserviceable tow bar being used to pull the aircraft broke. The aircraft ran onto the tug when the ground crew stopped the tug suddenly. As result of the collision with the tug the aircraft fuselage and landing gear was damaged.)
  • B744, Paris CDG France, 2003 (On 18 January 2003, a Boeing 747-400F being operated by Singapore Airlines Cargo on a scheduled cargo flight from Paris CDG to Dubai taxied for departure in darkness and fog with visibility less than 100 metres in places and the right wing was in collision with a stationary and unoccupied ground de/anti icing vehicle without the awareness of either the flight crew or anybody else at the time. Significant damage occurred to the de icing vehicle and the aircraft was slightly damaged. The vehicle damage was not discovered until almost two hours later and the aircraft involved was not identified until it arrived in Dubai where the damage was observed and the authorities at Paris CDG advised.)
  • Vehicle / B752, Dublin Ireland, 2009 (On 29 May 2009, a Boeing 757-200 being operated by UK Airline Thomson Airways on a passenger charter flight from Sharm-el-Sheikh, Egypt to Dublin and having just landed on runway 10 at destination at night in poor visibility overtook a small ride-on grass mower moving along the right hand side of the runway in approximate line with the aircraft’s right hand wing tip. The driver of the mower was unaware of the arriving aircraft until he heard it on the runway behind him. Prior to the landing, ATC had been informed that all grass-cutting equipment previously working on and around the runway had cleared it.)
  • Vehicle / E190 / E121, Jersey Channel Islands, 2010 (On 1 June 2010, an Airport RFFS bird scaring vehicle entered the active runway at Jersey in LVP without clearance and remained there for approximately three minutes until ATC became aware. The subsequent Investigation found that the incursion had fortuitously occurred just after an ERJ 190 had landed and had been terminated just as another aircraft had commenced a go around after failure to acquire the prescribed visual reference required to continue to a landing. The context for the failure of the vehicle driver to follow existing procedures was found to be their inadequacy and appropriate changes were implemented.)
  • ATP, Jersey Channel Islands, 1998 (On 9 May 1998, a British Regional Airlines ATP was being pushed back for departure at Jersey in daylight whilst the engines were being started when an excessive engine power setting applied by the flight crew led to the failure of the towbar connection and then to one of the aircraft's carbon fibre propellers striking the tug. A non standard emergency evacuation followed. All aircraft occupants and ground crew were uninjured.)

Aircraft/Object Conflict

  • B738, Surat India, 2014 (On 6 November 2014, a Boeing 737-800 taking off at night from Surat hit an object as it was approaching 80 knots and the take-off was immediately rejected. On return to the gate substantial damage was found to the left engine and a runway inspection found one dead buffalo and another live one. The runway was reopened after removal of the carcass but the live buffalo was not removed and was seen again by the runway the following day. The Investigation found a history of inadequate perimeter fencing and inadequate runway inspection practices at the airport.)
  • A319, London Heathrow UK, 2007 (On 12 February 2007, an Airbus A319-100 being operated by British Airways on a scheduled passenger flight into London Heathrow made unintended contact in normal daylight visibility with the stationary airbridge at the arrival gate. This followed an emergency stop made after seeing hand signals from ground staff whilst following SEGS indications which appeared to suggest that there was a further 5 metres to run to the correct parking position. There was no damage to the aircraft, only minimal damage to the airbridge and there were no injuries to the aircraft occupants or any other person)
  • B74S, Stockholm Arlanda Sweden, 1996 (On 14 June 1996, a Boeing 747SP being operated by Air China on a scheduled passenger flight from Beijing to Stockholm was arriving on the designated parking gate at destination in normal daylight visibility when it collided with the airbridge. None of the 130 occupants of the aircraft suffered any injury but the aircraft was “substantially damaged” and the airbridge was “damaged”.)
  • RJ85, Helsinki Finland 2010 (On 12 June 2010, a requested 22R runway inspection at Helsinki in normal daylight visibility carried out after a severe engine failure during the take off roll had led an Avro RJ85 being operated by Finnish Airline Blue1 on a scheduled passenger flight to Copenhagen to reject that take off at high speed. This inspection had not detected significant debris deposited on the runway during the sudden and severe engine failure. Two passenger aircraft, one being operated by Finnair to Dubrovnik, Croatia and the other being operated by Swedish airline TUIfly Nordic to Rhodes, Greece then departed the same runway before a re-inspection disclosed the debris and it was removed. Neither of the aircraft which used the runway prior to debris removal were subsequently found to have suffered any damage but both were advised of the situation en route.)
  • A321, Daegu South Korea, 2006 (On 21 February 2006, an Airbus A321-200 being operated by China Eastern on a scheduled passenger flight from Daegu to Shanghai Pudong failed to follow the marked taxiway centreline when taxiing for departure in normal daylight visibility and a wing tip impacted an adjacent building causing minor damage to both building and aircraft. None of the 166 occupants were injured.)
  • B737, Amsterdam Netherlands, 2003 (n 22 December 2003, a Boeing 737-700 being operated by UK Operator Easyjet on a scheduled passenger flight from Amsterdam to London Gatwick was taxiing for departure at night in normal visibility and took a different route to that instructed by ATC. The alternative route was, unknown to the flight crew, covered with ice and as a consequence, an attempt to maintain directional control during a turn was unsuccessful and the aircraft left wing collided with a lamp-post. The collision seriously damaged the aircraft and the lamp post. One passenger sustained slight injuries because of the impact. The diagram below taken from the official investigation report shows the area where the collision occurred.)
  • B773, Lisbon Portugal, 2016 (On 13 January 2016 ice was found on the upper and lower wing surfaces of a Boeing 777-300ER about to depart in the late morning from Lisbon in CAVOK conditions and 10°C. As Lisbon had no de-ice facilities, it was towed to a location where the sun would melt the ice more quickly but during poorly-planned manoeuvring, one of the wingtips was damaged by contact with an obstruction. The Investigation attributed the ice which led to the problematic re-positioning to the operator’s policy of tankering most of the return fuel on the overnight inbound flight where it had become cold-soaked.)
  • B734, Aberdeen UK, 2005 (Significant damage was caused to the tailplane and elevator of a Boeing 737-400 after the pavement beneath them broke up when take off thrust was applied for a standing start from the full length of the runway at Aberdeen. Although in this case neither outcome applied, the Investigation noted that control difficulties consequent upon such damage could lead to an overrun following a high speed rejected takeoff or to compromised flight path control airborne. Safety Recommendations on appropriate regulatory guidance for marking and construction of blast pads and on aircraft performance, rolling take offs and lead-on line marking were made.)

Related Articles

Further Reading