B738, Sydney Australia, 2007
From SKYbrary Wiki
|On 14 July 2007, a Boeing 737-800 being operated by New Zealand airline Polynesian Blue on a scheduled passenger service from Sydney to Christchurch New Zealand commenced take off on Runway 16R with asymmetric thrust set and veered off the side of the runway reaching the intersecting runway 07 before rejected take off action initiated by the flight crew took effect and the aircraft came to a stop.|
|Actual or Potential
|Human Factors, Runway Excursion|
|Flight Conditions||On Ground - Normal Visibility|
|Type of Flight||Public Transport (Passenger)|
|Actual Destination||Sydney Airport|
|Take off Commenced||Yes|
|Flight Phase||Take Off|
|Location - Airport|
|Tag(s)||Inadequate Aircraft Operator Procedures|
Procedural non compliance,
Inappropriate crew response - skills deficiency
|Damage or injury||No|
|Aircraft damage||None"None" is not in the list (Minor, Major, Hull loss) of allowed values for the "Aircraft damage" property.|
|Injuries||None"None" is not in the list (Few occupants, Many occupants, Most or all occupants) of allowed values for the "Injuries" property.|
|Fatalities||None"None" is not in the list (Few occupants, Many occupants, Most or all occupants) of allowed values for the "Fatalities" property. ()|
|Causal Factor Group(s)|
On 14 July 2007, a Boeing 737-800 being operated by New Zealand airline Polynesian Blue on a scheduled passenger service from Sydney to Christchurch New Zealand commenced take off on Runway 16R with asymmetric thrust set and veered off the side of the runway reaching the intersecting runway 07 before rejected take off action initiated by the flight crew took effect and the aircraft came to a stop.
An Investigation was carried out by the ATSB. It was was established that, with the aircraft commander as PF, the aircraft had entered Runway 16R via Taxiway ‘G’ with the intention of performing a rolling take off from that intersection using reduced thrust. Flight Data Recorder (FDR) data showed that as the aircraft neared this intersection, both engine thrust levers had been advanced together but whilst the left engine N1 had increased to 28%, the right engine N1 had remained steady at 20% RPM, equivalent to Idle.
The aircraft had entered the departure runway a groundspeed of 16 knots with the PF advancing the thrust levers and pressing the TO/GA button as the aircraft turned right onto runway heading with 30° still to go to the runway heading. At this point, the left engine N1 was 41% and the right engine N1 was at 24% with no stabilisation in engine acceleration at 40%. Whilst the thrust levers then moved forward equally towards the take-off thrust setting, engine thrust continued to increase more rapidly on the left engine because of its higher initial N1, and the aircraft continued turning to the right. The PF applied maximum left rudder input, but was unable to prevent the aircraft from turning past the runway heading and so retarded the thrust levers to Idle to reject the take off attempt.
It was found that just prior to the rejected take off action, the left engine N1 had reached the take-off setting of 98% whereas the right engine N1 had only reached 64% and that a maximum groundspeed of 30 knots had been attained. It was also found that the aircraft commander had not appreciated an increasing thrust asymmetry and had instead attributed difficulty in maintaining directional control as a problem with the nose-wheel steering and reacted accordingly with, eventually, maximum left nosewheel steering tiller deflection before the aircraft stopped.
The trajectory of the aircraft and the corresponding FDR parameters are shown on the diagram below taken from the ATSB Investigation Report.
The Investigation focused on the nature of acceleration (spool up) on the engines and included the following content, quoted verbatim, and the referenced “Figure 4” reproduced below, in the Investigation Report:
“High bypass turbo-fan engines of the type found on modern Boeing 737 aircraft do not accelerate in a linear manner when thrust is increased. The rate of acceleration increases as N1 increases (Figure 4), which was demonstrated by the characteristics of the engines during the acceleration sequence in this incident. The FDR readout depicts an expanded 25-second period across the engines’ thrust changes, showing recorded values of engine fuel flow and fan speeds, comparing the acceleration characteristics of the engines from idle. The red lines depict the characteristics of the right engine that commenced accelerating from an idle N1 setting. The blue lines depict the characteristics of the left engine that commenced accelerating from a higher initial N1 setting. The brown lines represent the acceleration of the right engine, moved 4 seconds earlier in the sequence, so that they overlay the acceleration phase of the left engine, to assist in making a comparison between the individual engines’ performance characteristics while accelerating.
The slopes of the blue and brown lines during the acceleration phase depicted in Figure 4 are approximately the same. This indicates that, if both engines had accelerated from the same N1 setting, their thrust would have remained symmetrical.
Just prior to the thrust on both engines being reduced, when N1 for each engine was 64% and 98% respectively, the left engine’s thrust would be about three times the right engine’s thrust, which can also be seen from the respective engine fuel flows depicted in Figure 4."
The Investigation noted that, as a result of this occurrence, the aircraft operator initiated a review of procedures for the training syllabus for recurrent and induction training. The review included briefing and assessment on the correct procedure for commencing a take-off roll. The briefing now includes:
- The correct procedures to be followed when commencing the take-off roll, including runway alignment prior to thrust application, engine stabilisation with symmetrical thrust prior to advancing thrust levers to take-off thrust (selecting TO/GA) and the use of the nose-wheel steering wheel during the take-off roll.
- Ensuring thrust is symmetrical and stabilised, and the aircraft aligned with the runway centreline before selecting TO/GA.
In addition, a low-speed rejected takeoff is to be completed during recurrent training and the correct take-off thrust setting procedures have been incorporated in induction training.
The Final Report of the Investigation was published on 18 February 2009 and may be seen at SKYbrary bookshelf: Aviation Occurrence Investigation AO-2007-023 Final
No Safety Recommendations were made.