If you wish to contribute or participate in the discussions about articles you are invited to join SKYbrary as a registered user
AP4ATCO - Units of Measurement and their Conversion
From SKYbrary Wiki
- ICAO Annex 5 - Units of Measurement to be Used in Air and Ground Operations.
- The following SKYbrary Articles:
Gain an understanding of:
- Units of measurement used in aviation
- Rules of thumb for conversion of units
Standard Units of Measurement
Units of measurement relevant for aircraft and principles of flight fall into six categories:
-vertical distance, -horizontal distance, -speed, -mass, -temperature -air pressure;
Standard units of measurement in aviation (Europe and North America) are shown in the following table:
|Category of Measurement||Unit of Measurement||Abbreviation|
|Horizontal Distance||nautical miles||nm|
|Horizontal Distance: RVR, Rwy length, and visibility <5km||meters||m|
|Vertical Distance: Flight Levels, heights and elevations||feet||ft|
|Vertical speed||Feet per minute||ft/min|
|Air Pressure||Hecto Pascals||hpa|
|Inches of mercury||In.Hg|
|Temperature and Dew Point||degrees Celsius||°C|
Flight crews on international routes encounter different units of measurement for setting barometric altimeters.Throughout Europe, hectoPascal (hPa) [or Millibar (mb)], is the primary altimeter setting (1 hPa = 1 mb). Within North America, the primary altimeter setting is In.Hg. In some parts of the world, such as Russia, levels are measured in metres (300 m = 1000 ft), speed only in km/hour, and wind speeds can be given in meters per second (m/s).
According to ICAO Annex 5 Contracting States are required to notify the Organization of any differences between their national regulations and practices and the International Standards contained in Annex 5.
Altimeter settings are occasionally misheard when listening to ATIS or ATC and the error may sometimes go undetected. When hPa is used as altimeter setting, an error of 10 hPa will correspond to approximately 300 feet error in indicated altitude.
Time is presented in a standard way by Co-ordinated Universal Time (UTC) The use of UTC is recommended by such bodies as the General Conference on Weights and Measures (CGPM), the International Radio Consultative Committee (CCIR) and the World Administration Radio Conference (WARC).
International Standard Atmosphere
Also known as the ICAO Standard Atmosphere, ISA is a standard against which to compare the actual atmosphere at any point and time.
The ISA is based the following values of pressure, density, and temperature at mean sea level each of which decreases with increase in height:
- Pressure of 1013.2 millibar - Pressure is taken to fall at about 1 millibar per 30 feet in the lower atmosphere (up to about 5,000 feet).
- Temperature of +15 °C59 °F <br />288.15 K <br />518.67 °R <br /> - Temperature falls at a rate of 2 °C35.6 °F <br />275.15 K <br />495.27 °R <br /> per 1,000 feet304.8 m <br /> until the tropopause is reached at 36,000 feet10,972.8 m <br /> above which the temperature is assumed to be constant at -57 °C. (The precise numbers are 1.98 °C35.564 °F <br />275.13 K <br />495.234 °R <br />, -56.5 °C-69.7 °F <br />216.65 K <br />389.97 °R <br /> and 36,090 feet11,000.232 m <br />)
- Density of 1,225 gm/m3.
The real atmosphere differs from ISA in many ways. Sea level pressure varies from day to day, and there are wide extremes of temperature at all levels.
Variation in pressure, vertically and horizontally, affects the operation of the pressure altimeter.
|Knots||1.85||Kilometre per hour|
|Kilometers per hour||0.54||Knots|
|Celsius||1.8 and add 32||Fahrenheit|
|Fahrenheit||Subtract 32 and multiply by 0.56||Celsius|
Q1: The most common unit of measurement of atmospheric pressure, HectoPascal (hPa) is often referred to as:?
- Inches of mercury (In. Hg)
- millimeters of mercury (mm Hg)
- millibars (mb)
Q2: One nautical mile is:
- 1852 meters or 5280 feet
- 1609 meters or 6076 feet
- 1852 meters or 6076 feet
Q3: In altimeter setting, an error of 10 hPa will correspond to approximately how many feet in indicated altitude?: