If you wish to contribute or participate in the discussions about articles you are invited to join SKYbrary as a registered user

Visual Scanning Technique

From SKYbrary Wiki
Article Information
Category: Loss of Separation Loss of Separation
Content source: SKYbrary About SKYbrary
Content control: EUROCONTROL EUROCONTROL

Description

Despite the value of electronic means of conflict detection (e.g. ACAS and STCA) visual lookout remains an important defence against loss of separation for all classes of aircraft. This is particularly true for pilots of light aircraft, many of which are single-pilot operated, are not equipped with ACAS or transponders and frequently operate VFR outside ATC radar cover and at low altitude. It is essential that these pilots develop sound visual scanning techniques.

This article is composed of extracts from the UK CAA Safety Sense Leaflet No 13 - 'Collision Avoidance' (see further reading). Although this article is directed towards pilots of light aircraft it is equally valid for all pilots, including those of large commercial aircraft.

Visual Scanning Technique

To avoid collisions you must scan effectively from the moment the aircraft moves until it comes to a stop at the end of the flight. Collision threats are present on the ground, at low altitudes in the vicinity of aerodromes, and at cruising levels.

Before take-off, check the runway visually to ensure that there are no aircraft or other objects in the take-off area. Check the approach and circuit to be sure of the position of other aircraft. Assess the traffic situation from radio reports. After take-off, continue to scan to ensure that there will be no obstacles to your safe departure.

During the climb and descent beware of the blind spot under the nose – manoeuvre the aircraft so that you can check.

Especially during climb or descent, listen to radio exchanges between air traffic and other aircraft and form a mental image of the traffic situation and positions of aircraft on opposing and intersecting headings, anticipating further developments. Scan with particular care in the area of airway (route) intersections and when near a radio beacon or VRP. You should remain constantly alert to all traffic within your normal field of vision, as well as periodically scanning the entire visual field outside the aircraft to ensure detection of conflicting traffic. Remember that the performance capabilities of many aircraft, in both speed and rates of climb/descent, result in high closure rates, limiting the time available for detection, decision, and evasive action.

How to Scan

The best way to develop effective scanning is by eliminating bad habits. Naturally, not looking out at all is the poorest scan technique! Glancing out at intervals of five minutes or so is also poor when considering that it takes only seconds for a disaster to happen. Check the next time the aircraft is climbing out or making an approach to see how long you spend without looking outside.

Glancing out and 'giving the old once-around' without stopping to focus on anything is practically useless; so is staring out into one spot for long periods of time.

There is no one technique that is best for all pilots. The most important thing is for each pilot to develop a scan that is both comfortable and workable.

Learn how to scan properly by knowing where and how to concentrate your search on the areas most critical to you at any given time. In the circuit especially, always look out before you turn to make sure your path is clear and that nothing is approaching from an area that will be hidden as you turn. Look out for traffic making an improper entry into the circuit.

During that very critical final approach stage, do not forget to scan all around to avoid tunnel vision. Pilots often fix their eyes on the point of touchdown. You may never arrive at the runway if another pilot is also aiming for the same runway threshold at that time!

In normal flight, you can generally avoid most of the risk of a mid-air collision by scanning an area at least 60° left and right of your intended flight path. Be aware that constant angle collisions often occur when the other aircraft initially appears motionless at about your 10 o'clock or 2 o'clock positions. This does not mean you should forget the rest of the area you can see. You should also scan at least 10° above and below the projected flight path of your aircraft. This will allow you to spot any aircraft that is at an altitude that might prove hazardous to you, whether it is level with you, climbing from below or descending from above.

The more you look outside, the less the risk of a collision. Certain techniques may be used to increase the effectiveness of the scan. To be most effective, the gaze should be shifted and refocused at regular intervals. Most pilots do this in the process of scanning the instrument panel but it is also important to focus outside the cockpit or flight deck to set up the visual system for effective target acquisition. Looking well ahead for weather and pre-planned navigation features can help. Proper scanning requires the constant sharing of attention with other piloting tasks, thus it is easily degraded by such conditions as distraction, fatigue, boredom, illness, anxiety or preoccupation.

Effective scanning is accomplished by a series of short, regularly-spaced eye movements that bring successive areas of the sky into the central visual field. Each movement should not exceed 10°, and each area should be observed for at least one second to enable detection. Although horizontal back-and-forth eye movements seem preferred by most pilots, each pilot should develop the scanning pattern that is most comfortable and then keep to it. Peripheral vision can be useful in spotting collision risks. It is essential to remember, however, that if another aircraft appears to have no relative motion, it is likely to be on a collision course with you. If the other aircraft shows no horizontal or vertical motion on the windshield, but is increasing in size, take immediate evasive action.

Scan Patterns

Two scanning patterns described below have proved to be very effective for pilots and involve the 'block' system of scanning. This system is based on the premise that traffic detection can be made only through a series of eye fixations at different points in space. In application, the viewing area (windshield) is divided into segments, and the pilot methodically scans for traffic in each block in sequential order.

Side-to-side scanning method

Start at the far left of your visual area and make a methodical sweep to the right, pausing very briefly in each block of the viewing area to focus your eyes. At the end of the scan, return to and scan the instrument panel and then repeat the external scan.

Side to side scanning technique
Side to side scanning technique

Front-to-side scanning method

Start in the centre block of your visual field (centre of front windshield); move to the left, focusing very briefly in each block, then swing quickly back to the centre block after reaching the last block on the left and repeat the action to the right. Then, after scanning the instrument panel, repeat the external scan.

Front to side scanning technique
Front to side scanning technique

There are other methods of scanning, of course, some of which may be as effective as the two described above. However, unless some series of fixations is made, there is little likelihood that you will be able to detect all targets in your scan area. When the head is in motion, vision is blurred and the mind will not register potential targets.

Related Articles

Further Reading