If you wish to contribute or participate in the discussions about articles you are invited to join SKYbrary as a registered user

Holdover Time

From SKYbrary Wiki

Jump to: navigation, search
Article Information
Category: Ground Operations Ground Operations
Content source: SKYbrary About SKYbrary
Content control: EUROCONTROL EUROCONTROL

Description

Holdover Time is the time for which it is expected that a given aircraft treatment by ground anti-icing fluid will remain valid. It is determined by the extent to which it is expected that applied fluid will remain on the aircraft surfaces to the extent necessary to provide protection from the accretion of frozen or semi frozen contaminants in the prevailing conditions. Holdover Time begins at the start of the anti icing operation. If a two-step operation is used, then it begins at the start of the final (anti-icing) step. By definition therefore, holdover time will have effectively run out when frozen deposits start to form or accumulate on treated aircraft surfaces.

Due to their properties, Type I fluids form a thin liquid wetting film, which provides only an extremely limited holdover time, especially in conditions of freezing precipitation. With this type of fluid no additional holdover time can be obtained by increasing the concentration of the fluid in the fluid/water mix. For ‘thickened fluids’ of Type 2, 3 and 4, their pseudo-plastic thickening agent enables the fluid to form a thicker liquid wetting film on aircraft surfaces which can then provide a significantly longer holdover time especially in conditions of continuing freezing precipitation. With this type of fluid additional holdover time will be provided by increasing the concentration of the fluid in the fluid/water mix, with maximum holdover time available from undiluted fluid.

Tables of Holdover Times for different fluids and prevailing conditions are published regularly and provide indication as to the time frame of protection that could reasonably be expected in each situation. These Tables contain elapsed time ranges which represent indicative maximum holdover times. The lower limit of the given time span indicates the estimated time of protection during moderate precipitation of the type stated and the upper limit indicates the estimated time of protection during light Precipitation of the type stated. The prevailing conditions are defined in HOT Tables as:

  • Active Frost - means when frost is forming and may occur when an aircraft surface temperature is at or below 0°C273.15 K
    32 °F
    491.67 °R     and also at or below the prevailing Dew Point,
  • Freezing Fog - fog prevails with an ambient temperature of 0°C273.15 K
    32 °F
    491.67 °R     or below so that rime ice is deposited on exposed surfaces.
  • Snow/Snow Grains - snow grains are defined as flat in form and with a diameter of less than 1mm and as not bouncing or shattering upon impact with hard ground.
  • Freezing Drizzle – uniform precipitation composed exclusively of closely spaced droplets with diameter less than 0.5mm which freezes upon impact with surfaces with a temperature at or below 0°C273.15 K
    32 °F
    491.67 °R    .
  • Light Freezing Rain – either as freezing drizzle but with widely separated droplets or composed of larger droplets falling at an intensity of no more than 2.5mm liquid water equivalent per hour.
  • Rain on Cold Soaked Wing – ‘cold soaked’ is the condition where a wing containing cold fuel acquires as a result a skin temperature at or below 0°C273.15 K
    32 °F
    491.67 °R     and is therefore vulnerable to the formation of clear ice on its surface in moist air up even when this air has a temperature of up to 15°C288.15 K
    59 °F
    518.67 °R    .

Heavy precipitation rates or high moisture content, high wind velocity or jet blast may reduce holdover time below the lowest time stated in the range and holdover times may also be reduced when aircraft skin temperature is lower than OAT.

Holdover time guidelines are published generically for the defined fluid Types 1, 2, 3 and 4 but are also sometimes given for individual fluid products. These “brand name” holdover times will be found to differ from the generic tables. There are no holdover times for Heavy Snow, Hail (defined as ice pieces between 5 and 50mm diameter), Snow or Ice Pellets (defined as hail of less than 5mm in diameter) and Moderate or Heavy Freezing Rain.

Related Articles & Further Reading

Retrieved from "http://www.skybrary.aero/index.php/Holdover_Time"
Personal tools