If you wish to contribute or participate in the discussions about articles you are invited to join SKYbrary as a registered user
Airborne Collision Avoidance System (ACAS)
From SKYbrary Wiki
Airborne Collision Avoidance System (ACAS)
The Airborne Collision Avoidance System II (ACAS II) was introduced in order to reduce the risk of mid-air collisions or near mid-air collisions between aircraft. It serves as a last-resort safety net irrespective of any separation standards.
ACAS II is an aircraft system based on Secondary Surveillance Radar (SSR) transponder signals. ACAS II interrogates the Mode C and Mode S transponders of nearby aircraft (‘intruders’) and from the replies tracks their altitude and range and issues alerts to the pilots, as appropriate. Non-transponding aircraft are not detected.
ACAS II works independently of the aircraft navigation, flight management systems, and Air Traffic Control (ATC) ground systems. While assessing threats it does not take into account the ATC clearance, pilot’s intentions or autopilot inputs.
Currently, the only commercially available implementations of ICAO standard for ACAS II (Airborne Collision Avoidance System) are TCAS II versions 7.0 and version 7.1 (Traffic alert and Collision Avoidance System). ICAO Annex 10 states that new ACAS installation after 1 January 2014 must be version 7.1 compliant and the existing units must be upgraded to version 7.1 before 1 January 2017.
Information Provided by ACAS
Two types of alert can be issued by ACAS II - TA (Traffic Advisory) and RA (Resolution Advisory). The former is intended to assist the pilot in the visual acquisition of the conflicting aircraft and prepare the pilot for a potential RA.
If a risk of collision is established by ACAS II, an RA will be generated. Broadly speaking, RAs tell the pilot the range of vertical speed at which the aircraft should be flown to avoid the threat aircraft. The visual indication of these rates is shown on the flight instruments. It is accompanied by an audible message indicating the intention of the RA. A "Clear of Conflict" message will be generated when the aircraft diverge horizontally.
The vertical sense (direction) of the RA is coordinated with other ACAS II equipped aircraft via a mode S link, so that two aircraft choose complementary manoeuvres. RAs aim for collision avoidance by establishing a safe vertical separation (300 - 700 feet), rather than restoring a prescribed ATC separation.
ACAS II operates on relatively short time scales. The maximum generation time for a TA is 48 seconds before the Closest Point of Approach (CPA). For an RA the time is 35 seconds. The time scales are shorter at lower altitudes (where aircraft typically fly slower). Unexpected or rapid aircraft manoeuvre may cause an RA to be generated with much less lead time. It is possible that an RA will not be preceded by a TA if a threat is imminent. The effectiveness of an RA is evaluated by the ACAS equipment every second and, if necessary, the RA may be strengthened, weakened, reversed, or terminated.
A protected volume of airspace surrounds each ACAS II equipped aircraft. The size of the protected volume depends on the altitude, speed, and heading of the aircraft involved in the encounter. See illustration below.
RAs can be generated before ATC separation minima are violated and even when ATC separation minima will not be violated. In Europe, for about two thirds of all RAs, the ATC separation minima are not significantly violated.
Types of RA (TCAS II version 7.0)
Types of RA (TCAS II version 7.1)
Complying with RAs
Pilots are required to comply immediately with all RAs, even if the RAs are contrary to ATC clearances or instructions.
If a pilot receives an RA, he/she is obliged to follow it, unless doing so would endanger the aircraft. Complying with the RA, however, will in many instances cause an aircraft to deviate from its ATC clearance. In this case, the controller is no longer responsible for separation of the aircraft involved in the RA.
On the other hand, ATC can potentially interfere with the pilot’s response to RAs. If a conflicting ATC instruction coincides with an RA, the pilot may assume that ATC is fully aware of the situation and is providing the better resolution. But in reality ATC is not aware of the RA until the RA is reported by the pilot. Once the RA is reported by the pilot, ATC is required not to attempt to modify the flight path of the aircraft involved in the encounter. Hence, the pilot is expected to “follow the RA” but in practice this does not yet always happen.
Some States have implemented “RA downlink” which provides air traffic controllers with information about RAs posted in the cockpit obtained via Mode S radars. Currently, there are no ICAO provisions concerning the use of RA downlink by air traffic controllers.
The International Civil Aviation Organization (ICAO) is responsible for the global standardisation of ACAS.
ACAS equipment is available from three vendors. While each vendor’s implementation is slightly different, they provide the same core functions and the collision avoidance and coordination logic contained in each implementation is the same. In order to be certified, ACAS equipment must meet the Minimum Operational Performance Standards (MOPS) laid down in RTCA and forthcoming EUROCAE documents.
The equipment which meets the ACAS II Standards and Recommended Practices (SARPs) is known as TCAS II, version 7. A joint RTCA/EUROCAE working group has finalised amendments to the MOPS, addressing three specific safety improvement changes related to the collision avoidance logic; these new MOPS will form TCAS II version 7.1 and are published as RTCA DO-185B and EUROCAE ED-143.
Types of ACAS
- ACAS I Gives Traffic Advisories (TAs) but does not recommend any manoeuvres. The only implementation of the ACAS I concept is TCAS I. ICAO Standards and Recommended Practices (SARPs) for ACAS I are published in ICAO Annex 10, volume IV but are limited to interoperability and interference issues with ACAS II. ACAS I is mandated in the United States for certain smaller aircraft
- ACAS II Gives Traffic Advisories (TAs) and Resolution Advisories (RAs) in the vertical sense (direction). ACAS II SARPs are published in ICAO Annex 10. The only implementations of the ACAS II concept are TCAS II Version 7.0 and Version 7.1. TCAS II Versions 7.0 and 7.1 are mandated in Europe and eleswhere.
- ACAS III Gives TAs and RAs in vertical and/or horizontal directions. Also referred to as TCAS III and TCAS IV. Not currently implemented and unlikely to be in the near future. ICAO SARPs for ACAS III have not been developed. Currently, there are no plans to proceed with such a development.
Amendment 85 to ICAO Annex 10 volume IV, published in October 2010, introduced a provision stating that:
- all new ACAS installations after 1 January 2014 shall be compliant with version 7.1; and
- all ACAS units shall be compliant with version 7.1 after 1 January 2017.
On 20 December 2011, the European Commission published an Implementing Rule mandating the carriage of ACAS II version 7.1 within European Union airspace earlier than the dates stipulated in ICAO Annex 10:
- by all aircraft with a maximum certified take-off mass exceeding 5,700 kg or authorised to carry more 19 passengers from 1 March 2012;
- with the exception of aircraft with an individual certificate of airworthiness issued before 1 March 2012, that must be equipped from 1 December 2015;
- aircraft not referred above but which will be equipped on a voluntary basis with ACAS II, must be equipped with version 7.1.
The safety benefits delivered by ACAS are usually expressed in terms of the risk ratio (does ACAS make safety better or worse?). For Europe, ACAS is estimated to reduce the risk of mid-air collision by a factor of about 5 (i.e. a risk ratio of 22%).
The importance of correctly following RAs is illustrated by the fact that a pilot who never follows RAs faces three times the risk that is faced by a pilot who always follows RAs. The human is the weakest element in the ACAS control loop; without “human in the loop” the risk ratio would improve by a factor of 10.
- Loss of Separation
- Level Bust
- TCAS II version 7.1
- ACAS Regulation and Procedures
- ACAS Resolution and Traffic Advisories
- ACAS: Guidance for Controllers
- ACAS Training
- Regulation 1332/2011 for laying down common airspace usage requirements and operating procedures for airborne collision avoidance
EUROCONTROL For further information, visit ACAS website:
- Overview of ACAS II - (incorporating version 7.1), Version 3.0 – 12 January 2012
- ACAS II Guide - Airborne Collision Avoidance System II (Incorporating version 7.1) - January 2012
- TCAS version 7.1 for pilots
- TCAS version 7.1 for controllers
- Safety Nets Awareness Toolkit
- ACAS Bulletins
- especially EUROCONTROL ACAS Bulletin no. 14 which deals specifically with ACAS II version 7.1
- Safety Nets Newsletters
- HindSight Articles:
- HindSight1: Level Bust - Advice for the ATCO;
- HindSight2: Analysis of an AIRPROX in Japan;
- HindSight4: Loss of Separation - A Lesson for the Instructor;
- HindSight5: TCAS and STCA - not just anagrams
- HindSight6: Changes to ICAO rules regarding TCAS RAs
- HindSight10: TCAS II and Level Bust
- HindSight11: Airbus altitude capture enhancement to prevent TCAS RAs
- HindSight12: TCAP: an altitude capture enhancement to prevent TCAS RAs
- HindSight14: STCA training - yes, we can!
- HindSight15: TCAS II version 7.1 has arrived
- HindSight16: Unnecessary TCAS RAs caused by high vertical rates before level off
Bureau d’Enquêtes et d’Analyses (BEA)
- ICAO Annex 10 Volume IV Chapter 4 and Attachment A ;
- ICAO Doc 4444: Procedures for Air Navigation Services (PANS-ATM) Chapter 15, Section 15.7.3
European Regulatory Documentation:
- IR-OPS CAT.IDE.A.155 - Airborne collision avoidance system (ACAS)
- IR-OPS CAT.OP.MPA.295 - Use of airborne collision avoidance system (ACAS)
- Acceptable Means of Compliance and Guidance Material CAT.OP.MPA.295
- IR-OPS ORO.GEN.160 - Occurrence Reporting
- EU-OPS 1.668: requirement for aircraft to be equipped with ACAS
- EU-OPS 1.398: use of TCAS
- EU-OPS 1.420: requirement to report TCAS RAs
- JAA TGL 11: Guidance for operators on training programmes for the use of ACAS